Siemens SPCW101 Snelstarthandleiding - Pagina 2

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Siemens SPCW101. Siemens SPCW101 9 pagina's. Siway rf-kit and rf-modules for panel and keypads/external antenna kit
Ook voor Siemens SPCW101: Installatie-instructie (8 pagina's), Snelstarthandleiding (6 pagina's)

Pagina afdrukken

English – Installation Instructions

WARNING - Before starting to install and work with this device, please read

the Safety Instructions.

When changing or installing a SPCW101/110/111/112/114 on the SPC

system, ensure that all anti-static precautions are adhered to while handling

connectors, wires, terminals and PCBs.

EC Declaration of Conformity

Siemens Security Products hereby declares that this product is in compliance with

the essential requirements and other relevant provisions of Directive 1999/5/EC on

Radio and Telecommunications Terminal Equipment (R&TTE) and 2004/108/EC

on Electromagnetic Compatibility (EMC) EN60950-1:2006+A1:2010.

The EC Declaration of Conformity is available from your Siemens sales office or:

Siemens AB, Security Products

Englundavägen 7

SE-171 24 Solna

Sweden

Product Description

The SiWay RF-Kit (SPCW110) and RF-Modules (SPCW111/112/114) provide a

wireless interface (868 MHz) for the controller and keypads enabling wireless

devices (for example, remote controls, magnetic contacts or motion detectors) to

be enrolled on the system.

The SPCW110/111/112/114 incorporate the following elements, as shown in

Fig. 1, 2, 3, and 4.

Fig. 1: SPCW110 (Panel Module)

1 Female SMA connector to attach an external antenna.

2 2 x 4 and 1 x 10 pin connectors

3 LED - activated when signals are received.

Fig. 2: SPCW111 (Panel Module)

1 Wireless antenna

2 2 x 4 and 1 x 10 pin connectors

3 LED - activated when signals are received.

Fig. 3: SPCW112 (Keypad Module for SPCK42x)

1 Wireless antenna

2 2 x 4 and 1 x 10 pin connectors

3 LED - activated when signals are received.

Fig. 4: SPCW114 (Keypad Module for SPCK52x)

1 Wireless antenna

2 LED - activated when signals are received.

3 1 x 10 pin connectors

Installing the SPCW110/111 in the SPC4xxx/5xxx/6xxx Housing

Only install the SPCW111 on a controller that is contained within a plastic

housing.

Fig. 7

Wireless module (SPCW110 shown)

Primary modem slot

1. Disconnect the mains supply.

2. Remove the cover and disconnect the battery.

3. Remove the modem from the primary modem slot on the controller if one is

installed.

4. Position the wireless module on the controller with the SMA connector/antenna

towards the top of the controller board.

5. Firmly but gently press down to secure the module (Fig. 5).

6. Replace the modem in the primary modem slot over the wireless module, if

one was previously installed.

7. Reconnect the battery and close the cover.

8. Reconnect the mains supply.

Installing the SPCW112 in the SPCK42x Keypad

1. Disconnect the power supply for the keypad.

2. Remove the keypad from the back cover by loosening the securing screw from

the bottom of the keypad and leveraging the access tabs using an appropriate

screwdriver.

3. Position the wireless module on the keypad PCB (Fig. 9).

Fig. 9

1 Keypad PCB

2 Wireless module

3 Wireless antenna

4 LCD display board

4. Firmly but gently press down to secure the module.

5. Replace the back cover of the keypad.

6. Reconnect power to the keypad.

Installing the SPCW114 in the SPCK52x Compact Keypad

1. Disconnect the power supply for the keypad.

2. Open the keypad by loosening the securing screw from the bottom of the

keypad and leveraging the access tabs using an appropriate screwdriver.

3. Remove the keypad front cover.

4. Position the wireless module on the keypad PCB (Fig. 10).

Fig. 10: Compact Keypad PCB

1 Tamper switch

2 Rotary switches

3 Wireless antenna

4 Wireless module PCB

5 Connector socket

5. Insert the pin connectors at the bottom of the module into the connector socket

(Fig. 6).

6. To close the unit, hook the top of the front cover into the securing lugs of the

keypad base and press downward. Press firmly to ensure that the two clips on

the base engage fully with the corresponding recesses in the front cover.

7. Reconnect power to the keypad.

Installing the External Antenna on a Metal Housing

Fig. 8: External Antenna

Locking nut

SMA male interface for connection to wireless receiver module

1. Locate the circular knockouts at the top of the metallic housing. Choose the

desired knockout and carefully knock out an access area.

2. Unscrew the locking nut from the antenna screw fitting and remove it

completely from the antenna lead. Retain the serated washer on the antenna.

3. Insert the antenna lead and the screw fitting down into the exposed knockout

opening and pull the lead through until the antenna is sitting flush on top of the

housing.

4. From within the housing, fit the nut over the antenna lead and onto the screw

fitting of the antenna.

5. Tighten the nut on the screw, securing the antenna onto the housing.

6. Screw the SMA male connector into the female connector on the wireless

receiver.

7. To enable the external antenna operation on the system (SPCW110 only), on

the keypad, enter Full Engineer mode.

8. Go to WIRELESS > EXTERNAL ANTENNA > ENABLED > SELECT. The

wireless antenna is installed (Fig.11).

Installing the External Antenna (SPCW101) for GSM or Wireless

Modules

The cable length of 2 metres allows a number of mounting positions to enhance

the wireless reception of a GSM or wireless module if necessary. The antenna can

be mounted on an external bracket outside the cabinet (Fig. 12).

1. Disconnect the mains supply.

2. Remove the cover and disconnect the battery.

3. Unscrew the locking nut from the antenna screw fitting and remove it

completely from the antenna lead. Retain the serated washer on the antenna.

4. Insert the antenna lead and the screw fitting down into the opening on the

bracket and pull the lead through until the antenna is sitting flush on top of the

bracket.

5. Underneath the bracket, fit the nut over the antenna lead and onto the screw

fitting of the antenna.

6. Tighten the nut on the screw, securing the antenna onto the bracket.

7. Screw the SMA male connector into the female connector on the GSM module

or wireless receiver.

8. Reconnect the battery and close the cover.

9. Reconnect the mains supply.

10. To enable the external antenna operation on the system (SPCW110 only), on

the keypad, enter Full Engineer mode.

11. Go to WIRELESS > EXTERNAL ANTENNA > ENABLED > SELECT. The

wireless antenna is installed (Fig.12).

Technical Data SPCW110/111/112/114

SiWay RF receiver (868 MHz)

Radio module

Max.10 mA at 12 VDC

Operating current

Max.10 mA at 12 VDC

Quiescent current

Operating temperature

-10 ~ +50 °C

Dimensions (W x H x D)

PCB: 50 x 22 x 20 mm

0.05 kg

Weight

2 m

Cable length SPCW101

Standards (SPCW110,

EN50131-3:2009, EN50131-5-3:2005+A1:2008

SPCW112 only)