Siemens CB774G1 1 Series Gebruikershandleiding - Pagina 26
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Siemens CB774G1 1 Series. Siemens CB774G1 1 Series 40 pagina's.
en Troubleshooting
Fault
The time is not dis-
played when the ap-
pliance is switched
off.
Appliance door can-
not be opened.
Home Connect is not
working properly.
The interior lighting
does not work.
Maximum operating
time reached.
Error code made up
of letters and num-
bers appears on the
display, e.g. E0111.
The cooking result is
not satisfactory.
21.2 Replacing the oven light bulb
If the light in the cooking compartment fails, change
the oven light bulb.
Note: Heat-resistant, 25-watt, 230 V halogen bulbs are
available from the after-sales service or specialist retail-
ers. Only use these bulbs. Hold the new halogen bulbs
only with a clean, dry towel. This increases the service
life of the bulb.
WARNING ‒ Risk of burns!
The appliance and its parts that can be touched be-
come hot during use.
Caution should be exercised here in order to avoid
▶
touching heating elements.
Young children under 8 years of age must be kept
▶
away from the appliance.
26
Cause and troubleshooting
Basic setting has been changed.
Change the basic setting for the time display.
▶
→ "Basic settings", Page 15
The cleaning function locks the appliance door;
Allow the appliance to cool down until goes out in the display.
▶
→ "Cleaning function 'Pyrolytic activeClean'", Page 19
The childproof lock locks the appliance door.
Use the
button to deactivate the childproof lock.
▶
→ "Childproof lock", Page 15
You can switch off the lock in the basic settings.
→ "Basic settings", Page 15
Different causes are possible.
Go to www.home-connect.com.
▶
The halogen lamp is defective.
Change the oven light bulb.
▶
→ "Replacing the oven light bulb", Page 26
To prevent an unwanted permanent operation, the appliance automatically stops heating
after several hours if the settings are unchanged. A message appears in the display.
The point at which the maximum operating time is reached is determined by the corres-
ponding settings for an operating mode.
To continue operation, switch the appliance off and on again using
1.
the operation.
If you do not need to use the appliance, press
2.
Tip: To prevent the appliance from switching off when you do not want it to, set a cooking
time.
→ "Time-setting options", Page 12
The electronics have detected a fault.
Switch the appliance off and on again.
1.
a If the fault was a one-off, the message disappears.
If the message appears again, call the after-sales service. Please specify the exact error
2.
message when calling.
→ "Customer Service", Page 27
Settings were unsuitable.
Adjustment values, e.g. temperature or cooking time, depend on the recipe, quantity and
food.
Next time, set lower or higher values.
▶
Tip: A lot of other information about the food preparation and corresponding adjustment
values can be found in the Home Connect app or on our website siemens-home.bsh-
group.com .
lights up in the display.
to switch it off.
WARNING ‒ Risk of electric shock!
When changing the bulb, the bulb socket contacts are
live.
Before replacing the bulb, ensure that the appliance
▶
is switched off in order to prevent a potential electric
shock.
Also unplug the appliance from the mains or switch
▶
off the circuit breaker in the fuse box.
Requirements
¡ The appliance is disconnected from the power sup-
ply.
¡ The cooking compartment has cooled down.
¡ You have a new halogen bulb to replace the old one.
Place a tea towel in the cooking compartment to
1.
prevent damage.
Turn the glass cover anti-clockwise to remove it .
2.
. Reset and start