Ricoh SP C250SF Instellingen Handleiding - Pagina 3
Blader online of download pdf Instellingen Handleiding voor {categorie_naam} Ricoh SP C250SF. Ricoh SP C250SF 4 pagina's. Color laser printer. color laser mfp
Ook voor Ricoh SP C250SF: Specificaties (4 pagina's)
Pagina afdrukken
Press the [ ] or [ ] key to
select [Setup Wizard], and then
Confi guring Settings Using the Con-
press the [OK] key.
trol Panel
•
You need to select the same authentication
method and encryption method that the
access point (router) is using. You can check
them on the settings screen of the access
Select [Infrastructure], and
point (router).
•
Make sure the Ethernet cable is not
then press [Next].
connected to the machine.
Check that the wireless LAN
access point (router) is working
correctly.
Press the [User Tools] key.
Search the SSID to display the
list, select the destination SSID,
and then press [Next].
If you cannot fi nd the destination SSID,
confi gure the SSID according to the
DAC509
following procedure.
Press the [ ] or [ ] key to
1. When entering the SSID, select [Input
select [Network Settings], and
SSID], and then press [Next].
then press the [OK] key.
2. Enter the SSID using the number keys,
and then press [Next].
The characters that can be used are
ASCII 0x20-0x7e (32 bytes).
If you are requested to enter a
password, enter the password
using the number keys, and then
For details about checking the SSID, see
press the [OK] key.
"Checking the SSID and Encryption
key".
Select the authentication
Press the [ ] or [ ] key to
method, and then press [Next].
select [Wi-Fi Confi guration],
and then press the [OK] key.
The next steps differ depending on the
authentication method that you have selected.
Proceed to Step 10 of the appropriate section.
•
If the authentication method is set to
[WPA2-PSK] or [Mix Mode WPA2/
WPA]
•
If the authentication method is set to
[Open System] or [Shared Key]
Connecting to devices using the
WPA2-PSK or Mix Mode WPA2/
WPA authentication
.
Enter the encryption key using
the number keys, and then press
[Connect].
2
•
As the passphrase, you can enter either
8 to 63 ASCII characters (0x20-0x7e)
or 64 hexadecimal digits (0-9, A-F,
a-f).
•
For details about checking the
encryption key, see "Checking the
SSID and Encryption key".
Press [Yes].
After connecting to the network, the
Wi-Fi screen is displayed.
Press the [ ] or [ ] key to
select [Wi-Fi Status], and then
press the [OK] key.
When "Connected" is displayed, the
connection has been established.
•
When "Connecting..." is displayed, the
connection is being established.
•
When "Disconnected" is displayed, the
connection has not been established.
Start again from the beginning.
The next step is to install the driver from
the CD-ROM provided.
For details, see Driver Installation Guide
on the CD-ROM provided.
Connecting to the devices using
the Open System or Shared Key
authentication
Select the encryption method,
and then press [Next].
For the encryption method, refer to the
following:
Confi guring Settings Using
Encryption
Encryption key
Web Image Monitor
Method
(Maximum number and type of
characters that can be entered)
When confi guring the settings manually, you
WEP 64 bit ASCII 5 characters (0x20-0x7e)
can also use Web Image Monitor. It is
WEP 64 bit Hex
10 characters (0-9, A-F, a-f)
convenient for entering characters that are
WEP 128 bit ASCII 13 characters (0x20-0x7e)
diffi cult to enter using the control panel.
WEP 128 bit Hex 26 characters (0-9, A-F, a-f)
Connect the Ethernet cable to
the Ethernet port.
•
Do not select [None] except in special
cirmunstances. If selected, the security
Plug the other end of the cable
system will not work.
into a network device, such as a
hub.
Enter the encryption key and
ID using the number keys, and
Launch the Web browser.
then press [Connect].
In the Web browser's address
bar, enter "http://(machine's IP
address)/" to access the
machine.
If a DNS or WINS server is used and the
For details about checking the encryption
machine's host name has been specifi ed,
key, see "Checking the SSID and
you can enter the host name instead of
Encryption key".
the IP address.
The ID is used for identifying the
encryption key. You can register four
Click [Network Settings].
encryption keys (ID 1 to 4).
Select [Wireless] tab.
Press [Yes].
Set [Wireless] to [Active].
Click [Scan List] to display the
list, select the destination SSID,
and then click [OK].
After connecting to the network, the
If you cannot fi nd the destination SSID,
Wi-Fi screen is displayed.
confi gure the SSID according to the
following procedure.
Press the [ ] or [ ] key to
1. In [SSID], enter the SSID for the
select [Wi-Fi Status], and then
access point (router).
press the [OK] key.
Set [Communication Mode] to
When "Connected" is displayed, the
[Infrastructure].
connection has been established.
In [Authentication], select the
authentication method.
In [Encryption], select the
encryption option.
•
When "Connecting..." is displayed, the
•
If the authentication method is set to
connection is being established.
[Open System], set the encryption
•
When "Disconnected" is displayed, the
option to [None] or [WEP].
connection has not been established.
•
If the authentication method is set to
Start again from the beginning.
[Shared Key], set the encryption option
The next step is to install the driver from
to [WEP].
the CD-ROM provided.
•
If the authentication method is set to
For details, see Driver Installation Guide
[WPA2-PSK], set the encryption
on the CD-ROM provided.
option to [CCMP (AES)].
•
If the authentication method is set to
[Mixed Mode WPA/WPA2], set the
•
A password for accessing the [Admin. Tools]
encryption option to [TKIP/AES].
menu can be specifi ed in [Admin. Tools
Lock].
❖
If the encryption method is set to
[None]
If you have selected [None], proceed to
Step 12.
❖
If the encryption method is set to
[CCMP (AES)] or [TKIP/AES]
1
DAC534
1. WPA Passphrase
Enter the password for the access
point (router).
As the passphrase, you can enter either
8 to 63 ASCII characters (0x20-0x7e)
or 64 hexadecimal digits (0-9, A-F,
a-f).
❖
If the encryption method is set to
[WEP]
1
2
3
4
DAC535
1. WEP Key Length
Select 64 bit or 128 bit.
2. WEP Transmit Key ID
Enter the ID.
3. WEP Key Format
Select ASCII or Hexadecimal.
4. WEP Key
Enter the password for the access
point (router).
Wi-Fi Settings Guide 2/2