Digitalk 2 - WAY COMMUNICATOR Gebruiksaanwijzing en handleidingen - Pagina 2

Blader online of download pdf Gebruiksaanwijzing en handleidingen voor {categorie_naam} Digitalk 2 - WAY COMMUNICATOR. Digitalk 2 - WAY COMMUNICATOR 5 pagina's.

Pagina afdrukken

Communicator Controls

17
16
15
14
DW
13
12
11
M
10

Getting Started

Carefully remove your communicator from its packing. If there is any
visible damage, do not attempt to operate this communicator. Return
it to the place of purchase
Removing the BELT CLIP:
Figure 1.
1. Pull the BELT CLIP LATCH away from the unit.
2. While pulling the BELT CLIP LATCH, push up on the BELT CLIP to remove
it from the unit. See Figure 1.
Installing the Belt Clip:
1. Slide the BELT CLIP into the BELT CLIP SLOT. See Figure 2.
2. A "click" indicates the BELT CLIP is locked into position.
1
2
3
BUSY
SCAN
VOX
4
5
C
6
7
8
9
4
Figure 2.
6
Communicator Controls
1. Antenna (Pg. 16, 18)
2. LCD Screen: Displays current channel selection and other radio status
symbols. (Pgs. 8-10, 12, 13)
3. Up
button (VOLUME/CHANNEL): Press to adjust volume level and
change channels. (Pgs. 9-11, 13-15)
4. Down
button (VOLUME/CHANNEL): Press to adjust volume level and
change channels. (Pgs. 9-11, 13-15)
5. Call C button: Press to transmit CALL TONES. (Pg. 11,13)
6. Enter
button: Used to turn LCD Screen LAMP ON/OFF Buttons
are locked when pressed and held. (Pg. 10, 11,13,14)
7. Speaker (Pg. 9)
8. Battery Compartment (LOCATED ON THE REAR): Houses 4 x "AAA"
alkaline or Ni-MH rechargeable batteries (not included). (Pgs. 7, 15)
9. Battery Compartment Cover Latch (LOCATED ON THE REAR): Secures
Battery Compartment cover. (Pg. 7)
10. Mic: Microphone. (Pgs. 9, 15)
11. Monitor M button: Press to tune in and hold onto weak signals. (Pgs.
9-11,13,15)
12. Menu
button: Allows you to change channels. (Pgs. 10,11, 13-15)
13. PUSH TO TALK PTT button: Press to transmit. (Pgs. 9,11, 13,14)
14. Power On/Off
button: Press and hold the button to turn your unit
ON/OFF. (Pgs. 7, 9)
15. TX (Transmission) LED indicator: Illuminates red when transmitting. (Pgs.
9, 11, 12, 14)
16. SP. Jack: When earphone is connected into this jack, voice of the
speaker will shift to earphone.
17. Belt Clip (LOCATED ON THE REAR) (Pg. 6)
18. Mic. Jack / Battery Charge Jack (Pg. 12)
Getting Started
Battery Installation:
Figure 3.
1. Release the BATTERY COMPARTMENT COVER LATCH located on the
rear side of the unit (see Figure 3) and remove the BATTERY
COMPARTMENT COVER from the BATTERY COMPARTMENT (See Figure
4).
2. Install 4x1.5V AAA alkaline batteries or Ni-MH rechargeable batteries
(not included) as shown.
3. Reinstall the BATTERY COMPARTMENT COVER and lock the BATTERY
COMPARTMENT COVER LATCH into position.
The COMMUNICATOR has a built in POWER SAVER feature for maximum
battery life. But when the COMMUNICATOR is not being used, conserve
battery power by pressing the
the unit will not be used for a long period of time.
5
Figure 4.
button to OFF. Remove the batteries if
7