Cisco Codec C Series Aan de slag handleiding - Pagina 20
Blader online of download pdf Aan de slag handleiding voor {categorie_naam} Cisco Codec C Series. Cisco Codec C Series 46 pagina's. Telepresence conference system
Ook voor Cisco Codec C Series: Aan de slag handleiding (41 pagina's), Gebruikershandleiding (44 pagina's), Aan de slag handleiding (35 pagina's), Aan de slag handleiding (32 pagina's), Aan de slag handleiding (42 pagina's)
Pagina afdrukken
Cisco TelePresence Video Systems
Contents
Configuring H.323 and SIP
(When not set by a provisioning system)
To get online and ready to place and receive calls, your system
must be set up properly. Your system uses either the H.323
protocol or the SIP protocol for video calls.
NOTE:
Contact your system administrator, or service provider,
for information about the network settings.
For networks administered through Cisco TMS (Cisco
TelePresence Management Suite), your Cisco TMS adminis-
trator will help you to get online.
You can find information about administering through Cisco UCM
in the
Administering TC endpoints on CUCM
Always save the new value when you change a setting
• Drop down list selection: Navigate to the correct value
and press the
OK
( ) key to save, or press the left arrow
key
to leave without saving.
• Text entry in an input field: Enter the text, navigate to
Ok/Save
to save the change, or navigate to
to leave without saving; then press the
confirm.
Back to task overview
D14639.15 Video Systems Getting Started Guide TC7.2, OCTOBER 2014.
Introduction
User interfaces
H.323
If in doubt for any of the parameters below, contact your system
administrator or your service provider.
1. Go to
Home > Settings > Administrator settings > Advanced
configuration > H323 > Profile
2. Go to
H323Alias
corresponding input fields.
3. If you want the system to obtain the H.323 gatekeeper
address automatically, go to
in the
Discovery
guide.
address manually, select
If set to Manual, enter the gatekeeper address in the
Address
input field.
4. If the H.323 gatekeeper requires authentication, and you
want your system to authenticate itself to the gatekeeper,
go to
Authentication
list.
Enter the
ing input fields.
If authetification is not needed, select
down
list.
5. Go to
Home > Settings > System information
H.323 settings.
If you have successfully registered to the Gatekeeper, the
Status
is shown as
6. Press
Home
If you wish to change the other H.323 settings, check the admin-
istrator guide for your product.
Cancel
OK
( ) key to
Configuration
Configuration
1.
and enter the
E164
number and
ID
in the
Gatekeeper
and select
drop down list; if you want to enter the
Manual.
and select
On
in the
Mode
drop down
LoginName
and
Password
in the correspond-
Off
in the
Mode
and verify the
Registered
in the H323 section.
(
) to exit.
20
Appendices
SIP
If in doubt for any of the parameters below, contact your system
administrator or your service provider.
1. Go to
Home > Settings > Administrator settings > Advanced
configuration > SIP > Profile
2. Go to
URI
and enter the SIP URI in the corresponding input
field.
3. Select your preferred
DefaultTransport
Auto
down list. If you select Auto, the system first tries to connect
using Tls, then TCP, and finally UDP.
4. Select your preferred proxy
default type is Standard.
5. Go to
Proxy 1.
If you want the system to obtain the SIP
proxy address automatically, select
drop down list; if you want to enter the address manually,
select Manual.
If set to Manual, enter the proxy address in the
input field.
drop
6. If the SIP proxy requires authentication, you must enter a
login name and password to authenticate your system. Go
to
Authentication 1
and enter the
in the corresponding input fields.
7. Go to
Home > Settings > System information
the SIP settings.
If you have successfully registered to a SIP server, the
Status
is shown as
Registered
8. Press
Home
(
) to exit.
If you wish to change the other SIP settings, check the admin-
istrator guide for your product.
Copyright © 2010–2014 Cisco Systems, Inc. All rights reserved.
Getting Started Guide
Contacts
1.
protocol in the drop
Type
in the drop down list. The
Auto
in the
Discovery
Address
LoginName
and
Password
and verify
in the SIP section.