Cisco Quick Set C20 Handleiding voor probleemoplossing - Pagina 19

Blader online of download pdf Handleiding voor probleemoplossing voor {categorie_naam} Cisco Quick Set C20. Cisco Quick Set C20 37 pagina's. Tc7.3, english, december 2015
Ook voor Cisco Quick Set C20: Aan de slag handleiding (41 pagina's), Gebruikershandleiding (44 pagina's), Aan de slag handleiding (42 pagina's), Aan de slag handleiding (35 pagina's), Snelle referentiehandleiding (2 pagina's), Snelle referentiehandleiding (2 pagina's), Gebruikershandleiding (25 pagina's), Installatieblad (2 pagina's), Snelle referentiehandleiding (2 pagina's), Snelle referentiehandleiding (2 pagina's), Aan de slag handleiding (32 pagina's), Gebruikershandleiding (48 pagina's), Aan de slag handleiding (42 pagina's), Aan de slag handleiding (46 pagina's)

Pagina afdrukken

Cisco Quick Set C20 Handleiding voor probleemoplossing

Remote control

The systems that do not have a Touch panel are controlled with a remote control. The remote control's

ir codes are picked up by the ir sensor in the camera. The codecs do have ir sensors, but these are

set to Off if a camera is detected (control signal).

if you are having problems with the remote control, check the following.

•

replace the batteries.

•

Check the short range/long range -switch inside the battery compartment. if the remote only

works when held within a few centimeters or an inch of the camera, it is set to short range.

•

Check that there is no Touch panel paired to the system. if a Touch is paired, the remote control

will be disabled. You can check if there is a Touch paired by going to

if you see the information below, the system is paired with a Touch panel.

•

Check that the camera is detected by the system.

•

Check the

Configuration -> Cameras

•

Check

Configuration -> System Unit

Figure 16 - Touch Panel Pairing Information

Confirming the key presses are received

You can confirm that key presses are being received by the codec in the system by using the command

line interface. login as admin using SSH and enter the command: xfeedback register /event

result:

xfeedback register /event

** end

When a key is pressed you will now see an event generated in the SSH session output. The actual

key presses are masked by "*" for privacy, but this output will confirm that input is received from the

remote control.

*e KeyDown Key: "*"

** end

*e KeyRelease Key: "*"

** end

*e KeyDown Key: "*"

** end

D15029.01 Troubleshooting Guide TC6.0, April 2013.

Configuration -> Peripherals.

and check that the IRSensor is set to On.

and check that the IRSensor is set to Auto.

System

Backup and restore configuration

Backup configuration

To take a backup of the system configuration go to

Take backup.

Figure 17 - Taking a Backup of System Configuration

You will now be asked where to save the configuration file. it is named configuration.tsh by default, but

it can be renamed. This file is a text file.

You can press the

Preview backup...

button if you want to see the configuration that will be backed up

when you press

Take

backup.

Restore configuration

if you are having a problem with the system and choose to factory reset it, restoring a previously taken

backup may re-introduce the problem. it may be worth reconfiguring the system by using the backup

configuration.

To restore a backup go to

Maintenance -> Backup and Restore

backup file taken previously (default name – configuration.tsh). Select this file and press

Figure 18 - Browse for Backup File

Figure 19 - Restore Configuration

NOTE

Currently the web snapshot setting will not be restored for security reasons.

Troubleshooting Guide TC6.0

Maintenance -> Backup and Restore

and press on

and press

Browse...

and locate the

Restore.