Cisco TelePresence Profile 42 Installatie

Blader online of download pdf Installatie voor {categorie_naam} Cisco TelePresence Profile 42. Cisco TelePresence Profile 42 2 pagina's. Telepresence ex, mx, quick set c20, codec c, sx20 quick set, profile series video systems
Ook voor Cisco TelePresence Profile 42: Aan de slag handleiding (42 pagina's)

Pagina afdrukken

Installing Cisco TelePresence System Profile 42"/55"

PRofile 42"/55" ConTAins:

Monitor

Bottom module:

• Column

• Foot module (stand-alone, wheelbase

or wall mount)

Front grille (inside foot module box)

Speaker grille (inside monitor box)

Camera

Microphones, 2 or 3 pcs.

Touch 8" interface device

Remote control

Cables, screws and tools

Cleaning cloth

Unpacking the foot module (stand-alone, wall mount or wheelbase)

Open the snap lockers.

Lift out the foot module box.

Open the box and unpack the

foot module.

Foot module box

The fooT ModUle Box ConTAins:

• Foot module (stand-alone, wall

• Four M8×30 screws

mount or wheelbase)

(wheelbase only)

• Front grille (not for wheelbase)

• Wall brackets and four M6×10

screws (wall mount only)

• Four M8×50 screws (not for

wheelbase)

A + B:

Mounting the stand-alone or the wall mount foot modules

to complete the bottom module

CAUTion:

Two persons working together are required to

mount the column to the foot module. Take care to hold

the modules firmly during installation.

Unpack the column. Hold it firmly while moving the foot

module towards the bottom of the column, aligning the

holes for the screws.

Fasten the four M8×50 screws with the

Allen key.

Raise the bottom module.

Rev. Date

Prep.

Checked Change

Stand-alone foot module (55 lb /25 kg)

heAVy

CAUTion

Lift out to open

the snap lockers.

Wall mount foot module

Wheelbase foot module

• Allen key

• Torx key (not for wheelbase)

• Level adjustment tool

(stand-alone only)

fAsTening The fRonT gRille

The front grille is attached using one M6×16 screw (upper

screw) and one M6×10 screw (lower screw) on each side,

as illustrated to the right. Use the Torx key.

The grille and Torx key are found in the foot module box. The

screws are pre-mounted in the grille and bottom module.

Follow these steps to fasten the grille:

Remove the two upper screws from the grille.

Loosen the two lower screws in the bottom module

without removing them.

Place the front grille below the front door, as illustrated

to the right. Tilt the front grille to get the brackets

behind the front door and slide the grille on to the

lower screws.

Open the front door to gain access to the screws.

Insert the upper screws without tightening them.

Close the front door to align the grille.

Open the front door again, and tighten the lower

screws through the hole.

Tighten the upper screws.

PReCAUTions

Please follow the steps in this installation guide when unpacking

and assembling Profile 42"/55". At least two (2) persons working

together are required when installing the system.

UnPACking The sysTeM AT The desTinATion

It is highly recommended to start the unpacking and assembling

of Profile 42"/55" at the place where the system is to be used.

noTe:

If it is not possible to bring the complete delivery to the

room where Profile 42"/55" is to be used, then unpack (step 1–2)

and bring the smaller units to the destination.

• The monitor box requires two (2) persons to lift

(42" 110 lb / 50 kg; 55" 121 lb / 55 kg)

• The column requires two (2) persons to lift (55 lb / 25 kg)

• The stand-alone foot module requires two (2) persons to lift

(55 lb / 25 kg)

Removing the outer cover and locating the boxes for the monitor, column, camera, touch screen and accessories

heAVy

Front

CAUTion

Monitor

(42" 110 lb / 50 kg,

55" 121 lb / 55 kg)

Column

(55 lb / 25 kg)

Front

heAVy

CAUTion

Front

Detailed illustration from inside, left

hand side. Right hand side is similar.

Upper screw

(M6×16)

Hole to access

the lower screw

Front grille

Lower screw

(M6×10)

Detailed illustration, left hand side.

Right hand side is similar.

Page 1

insTAllATion neAR A soCkeT-oUTleT

The equipment must be installed near a socket-outlet. The

socket-outlet shall be easily accessible after installation.

RooM gUidelines

noTe:

The floor must be in level.

The recommended distance between the Profile 42"/55" and

the meeting room table should be minimum 59 in. / 150 cm.

Read more about room guidelines in the Video conferencing room

primer.

UseR doCUMenTATion

The user documentation for this product, including compliance

and safety information, is available on the Cisco web site.

Go to: http://www.cisco.com/go/telepresence/docs.

Rev. Date

Prep.

Checked Change

The ACCessoRies Box ConTAins:

Telecom AS

Sheet 1 of 1

Processes

Tolerances

Specification:

Material

Type:

European

121608 rev.

Manufacturer:

projection

Type number:

Thickness:

Unit:

Dimensions without paint or finish

Color:

Sheet size:

All materials, finishes, and proccesses

Surface:

must comply with the RoHS directives

Glossiness:

Scale:

1:7

Flame class:

3D CAD model file 121608 rev. 01 is master

Part weight:

Flame class requirement: -

UL reference:

Mounting the wheelbase foot module

CAUTion:

Two persons working together are

required to mount the column to the wheelbase. Take

care to hold the modules firmly during installation.

Unpack the column. Hold it firmly while moving

the wheelbase towards the bottom of the column,

aligning the holes for the screws.

Use the Allen key, which is

found in the foot module

box, to fasten the four

Front door

M8×30 screws.

Raise the complete

bottom module.

Telecom AS

Sheet 2 of 2

Processes

Tolerances

Speci cation:

Material

Surface treatment

Type:

European

117324 rev.00A+

Manufacturer:

projection

Type number:

Thickness:

TANDBERG Aquarius 52"

Dimensions without paint or nish

Unit:

Color:

Sheet size:

All materials, nishes, and proccesses

Surface:

Glossiness:

Scale:

1:5

must comply with the RoHS directives

Flame class:

3D CAD model le 117324

rev. 00E+ is master

Part weight:

53908g

Flame class requirement: -

UL reference:

Rev. Date

Prep.

Checked Change

Telecom AS

117324 rev.00A+

TANDBERG Aquarius 52"

diMensions of PRofile 42"

The assembled unit has the following dimensions:

• Height: 59.9 in. / 152 cm

• Width: 38.6 in. / 98 cm

• Depth: Stand-alone: 26.8 in. / 68 cm

Wall mount: 8.9 in. / 23 cm (brackets included)

Wheelbase: 31.8 in. / 81 cm

• Weight: 232 lb / 105 kg

diMensions of PRofile 55"

The assembled unit has the following dimensions:

• Height: 64.6 in. / 164 cm

• Width: 49.6 in. / 126 cm

• Depth: The same as Profile 42"

• Weight: 245 lb / 111 kg

Touch controller

Camera

Accessories box

Surface treatment

• Microphones, 2 or 3 pcs.

• Cleaning cloth

• Remote control and 4 AAA

• Power cables

batteries

• Two M8×60 screws

Sheet 1 of 2

Processes

Tolerances

Specification:

Material

Surface treatment

Type:

European

Manufacturer:

projection

Type number:

Thickness:

Unit:

Dimensions without paint or finish

Color: