Sony SA-WCT291 Servicehandleiding - Pagina 2
Blader online of download pdf Servicehandleiding voor {categorie_naam} Sony SA-WCT291. Sony SA-WCT291 24 pagina's. Sound bar and active speaker system
Ook voor Sony SA-WCT291: Servicehandleiding (42 pagina's)
SA-WCT290/WCT291
NOTES ON CHIP COMPONENT REPLACEMENT
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
0.15 μF
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE
THESE
COMPONENTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
2
AC
1.5 kΩ
voltmeter
(0.75 V)
Earth Ground
WITH
SONY
PARTS
TABLE OF CONTENTS
1.
2.
2-1. Disassembly Flow ...........................................................
2-2. SUB MAIN Section ........................................................
2-3. SUB MAIN Board ..........................................................
2-4. Switching Regulator .......................................................
2-5. SUB KEY Board, Bluetooth Module ..............................
2-6. SUB LED Board, Front Panel Assy ................................
2-7. Loudspeaker (130mm)-203-11 ....................................... 10
3.
4.
POWER SUPPLY Section - ............................................ 13
4-2. Printed Wiring Board
- SUB MAIN Board (Component Side) - ....................... 15
4-3. Printed Wiring Board
- SUB MAIN Board (Conductor Side) - ......................... 16
4-4. Printed Wiring Board - SUB KEY Board - ..................... 17
4-5. Schematic Diagram - SUB KEY Board -........................ 17
4-6. Printed Wiring Board - SUB LED Board - ..................... 18
4-7. Schematic Diagram - SUB LED Board - ........................ 18
5.
5-1. Back Panel Section ......................................................... 19
5-2. SUB MAIN Section ........................................................ 20
5-3. Speaker Cabinet Section ................................................. 21
6.
.............................................
.......................................... 11
.............................. 22
3
6
6
7
8
8
9