Cisco ASR 9000 Series Configuratiehandleiding - Pagina 45
Blader online of download pdf Configuratiehandleiding voor {categorie_naam} Cisco ASR 9000 Series. Cisco ASR 9000 Series 50 pagina's. Line card
Ook voor Cisco ASR 9000 Series: Netwerkinstellingen configureren (26 pagina's), Configuratiehandleiding (46 pagina's), Handmatig (24 pagina's), configureren (46 pagina's), Handmatig (44 pagina's), Snelle referentiehandleiding (7 pagina's)
Pagina afdrukken
Configuring Serial Interfaces on the Cisco ASR 9000 Series Router
RP/0/0RP0RSP0/CPU0:router(config-if)# end
Uncommitted changes found, commit them? [yes]: yes
The following example shows how to configure the interval between keepalive messages to be 10
seconds:
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/3/0/0/0:0
RP/0/0RP0RSP0/CPU0:router(config-if)# keepalive 10
RP/0/0RP0RSP0/CPU0:router(config-if)# commit
The following example shows how to modify the optional serial interface parameters:
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/3/0/0/0:0
RP/0/0RP0RSP0/CPU0:Router(config-if)# serial
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# crc 16
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# invert
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# scramble
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# transmit-delay 3
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# commit
The following is sample output from the show interfaces serial command:
RP/0/0RP0RSP0/CPU0:Router# show interfaces serial 0/0/3/0/5:23
Serial0/0/3/0/5:23 is down, line protocol is down
Hardware is Serial network interface(s)
Internet address is Unknown
MTU 1504 bytes, BW 64 Kbit
Encapsulation HDLC, crc 16,
Last clearing of "show interface" counters 18:11:15
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
Configuring a Serial Interface with Frame Relay Encapsulation: Example
The following example shows how to create a serial interface on a SPA with Frame Relay encapsulation
and a serial subinterface with a PVC on router 1:
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/1/0/0
RP/0/0RP0RSP0/CPU0:router(config-if)# encapsulation frame-relay
RP/0/0RP0RSP0/CPU0:router(config-if)#frame-relay intf-type dce
RP/0/0RP0RSP0/CPU0:router(config-if)# no shutdown
RP/0/0RP0RSP0/CPU0:router(config-if)# end
Uncommitted changes found, commit them? [yes]: yes
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/1/0/0.1 point-to-point
OL-26061-03
reliability 143/255, txload 1/255, rxload 1/255
2764 packets input, 2816 bytes, 3046 total input drops
0 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 0 multicast packets
0 runts, 0 giants, 0 throttles, 0 parity
3046 input errors, 1 CRC, 0 frame, 0 overrun, 2764 ignored, 281 abort
2764 packets output, 60804 bytes, 0 total output drops
Output 0 broadcast packets, 0 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Cisco ASR 9000 Aggregation Services Router Interfaces and Hardware Component Configuration Guide
loopback not set, keepalive set (10 sec)
Configuration Examples for Serial Interfaces
543