Crow TLC-360 Installatie-instructies

Blader online of download pdf Installatie-instructies voor {categorie_naam} Crow TLC-360. Crow TLC-360 2 pagina's. 4 element ceiling mount passive infrared detector

Pagina afdrukken

TLC-360

4 ELEMENT

CEILING MOUNT

PASSIVE INFRARED DETECTOR

INSTALLATION INSTRUCTIONS

P/N 7151069

REV.E A.Y.

MOUNTING THE DETECTOR

Choose location most likely to intercept an

intruder. Refer to the detection pattern.

1. Hold the detector in your hand and

release the mounting plate by turning it

counter-clock-wise, and separate it

from the case (Fig. 1).

2. Insert the wires through the hole in the

center of the mounting plate (Fig. 2).

3. Mount the plate using the holes marked

mounting holes.

WIRE SIZE REQUIREMENTS

Use #22 AWG (0.5 mm) or wires with a

larger diameter. Use the following table to

determine required wire gauge (diameter)

and length of wire between the detector and

the control panel.

Wire Length

m 200 300

Wire Diameter mm .5

.75

Wire Length

ft. 800 1200 2000 3400

Wire Gauge

TERMINAL BLOCK CONNECTIONS

Run the cable through the cable entry hole

and connect the wires in accordance with

the following instructions:

Terminal 1 - Marked " - " ( GND )

Connect to ground of the control panel.

Terminal 2 - Marked " + " ( + 12V )

Connect to a positive Voltage output of 8.2-

16 Vdc source (usually from the alarm

control unit).

Terminals 3 & 4 - Marked " RELAY "

These are the output relay contacts of the

detector. Connect to a normally closed zone

in the control panel.

Terminals 5 & 6 - Marked " TAMPER "

If a Tamper function is required connect

TLC-360 FEATURES

∗ Fully sealed sensor chamber.

∗ VLSI Technology (Very Large Scale

Integration).

∗ Maximum RFI & EMI Immunity.

∗ 4 Element Pyro Sensor.

∗ Pulse Count.

∗ Sophisticated signal processing.

∗ Memory function.

∗ Hard Spherical Lens 360° coverage.

∗ Bidirectional temperature compensation.

∗ Flourescent light stability.

INTRODUCTION

The TLC-360 is a 4-element passive infrared

intrusion detector for use in electronic

security systems in ceiling mount

applications.

You will obtain optimum performance from

your TLC-360 PIR detector by following this

manual.

FIG. 1 - TLC-360 . EXTERNAL VIEW

OPEN

Separate cover

from base

400

800

1.0

1.5

these terminals to a 24 hour normally closed

protective zone in the control unit. If the front

cover of the detector is opened, an

immediate alarm signal will be sent to the

control unit.

Terminal 7 - Marked " MEM "

End Of Line option

The TLC-360 reduces false alarms to an

unprecedented minimal level due to its

effective elimination of background noises and

nuisance stimuli. The TLC-360 employs

Automatic Pulse Count making it extremely

adaptable to various environments. The

unique VLSI, using sophisticated signal

processing, makes this detector virtually free

of false alarms.

The TLC-360 integrates VLSI & SMD

(surface mount device) to their full advantage.

The detector is easy to install, with no

necessary adjustments.

HARD SPHERICAL LENS

The TLC-360 is equipped with a special hard

lens. This lens is the latest development in the

security field and complies with all the new

standards requirements. It gives wide

coverage patterns, even at low mounting

heights. It is especially immune to sunlight,

halogen lights and fluorescent lights and is

impervious to attack.

FIG. 2 - TLC-360. INTERNAL VIEW

Pulse Count /

Terminal Strip

LED Enable Switch

Rubber

Insulation

Sensitivity/Range

Adjustment

PULSE COUNT /LED Enable DIP Switch

(Fig.3 and DIP-SWITCH Setting).

To change positions of the DIP-switch you

have to open the detector:

1. Turn the detector counter-clock wise and

separate it from the mounting base.

2. Change position of the switch.

3. Close the detector and reinstall assembly

screws.