Acuity Controls ECLYPSE A1000 Installatiehandleiding - Pagina 12

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Acuity Controls ECLYPSE A1000. Acuity Controls ECLYPSE A1000 14 pagina's. Asset tracking
Ook voor Acuity Controls ECLYPSE A1000: Installatiehandleiding (10 pagina's)

Pagina afdrukken

Acuity Controls ECLYPSE A1000 Installatiehandleiding

8-0 Additional Information

8-1 Maintenance

Turn off power before any kind of servicing.

Regular Maintenance: Each controller requires minimal maintenance, but it

is important to take note of the following:

•

Clean the outside of the controller by polishing it with a soft dry

cloth.

•

Retighten terminal block connector screws annually to ensure the

wires remain securely attached.

8-2 Disposal

The Waste Electrical and Electronic Equipment (WEEE) Directive sets out

regulations for the recycling and disposal of products. The WEEE2002/96/

EG Directive applies to standalone products, for example, products that can

function entirely on their own and are not a part of another system or piece

of equipment.

For this reason Acuity products are exempt from the WEEE Directive.

Nevertheless, Acuity products are marked with the WEEE symbol ,

indicating devices are not to be thrown away in municipal waste.

Products must be disposed of at the end of their useful life according to

local regulations and the WEEE Directive.

8-3 North American

Emissions Compliance

United States:

Changes or modifications not expressly approved by

Acuity could void the user's authority to operate the

equipment.

•

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential and

commercial installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for

help.

8-3 North American Emissions

Compliance - cont'd

Canada:

•

This Class (B) digital apparatus meets all the requirements of

the Canadian Interference-Causing Equipment Regulations.

•

Cet appareil numérique de la Classe (B) respecte toutes les

exigences du Règlement sur le matériel brouilleur du Canada.

8-4 Complementary Information

The Power Supply Module (100-240VAC) is designed for type 1 action and

type 1.b action. The EMC immunity test passed using 230 VAC and 0.5

A. The Ball pressure Test temperature was 167°F (75°C) for the Enclosure

and 257°F (125°C) for the Connectors. The SELV must not exceed 42 VDC.

The maximum accessible voltage is 19 VDC. All connecting cables must be

permanently installed with X-type anchors. All cables must have insulation

rated for 176°F (80°C) or higher. These products are classified as integrated

electronic operation control devices. SELV is guaranteed by reinforced

insulation.

For the Power Supply Module (100-240VAC): Risk

of electric shock. Do not open. This product has no

user-serviceable parts inside. When power has been

disconnected, dangerous residual internal voltages may

still be present. Return this unit to Acuity for maintenance

or repair.

12 of 14