Motorola MJ273R Gebruikershandleiding - Pagina 2

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Motorola MJ273R. Motorola MJ273R 2 pagina's. Two-way radio talkabout

Motorola MJ273R Gebruikershandleiding
1. Press
until
appears on the display. The current setting
On/Off will flash.
2. Press
or
to select On or Off.
3. Press
to set or
to continue set up.
Hands-Free Use With Accessories (
)
You can transmit hands-free more reliably with the use of optional headset
accessories. Once VOX is turned on, the radio detects your voice and
transmits when you speak.
Many accessories (sold separately) are available for your radio. For more
information, visit our website at www.motorolasolutions.com/talkabout.
1. Turn the radio off and plug the VOX accessory into the accessory port.
2. Turn the radio on. VOX shows on the display.
3. Adjust the volume appropriately by rotating
. Lower the volume
before placing the accessory on your head or in your ear.
4. To turn off, simply remove accessory.
Note: There is a short delay between the time you start talking and when
the radio transmits. There is a short delay before the transmission is
completed.
Setting the Sensitivity Level When in
or
Mode
Adjusting the radio's sensitivity level helps minimize the possibility of
unintended noises triggering a transmission and helps the radio pick up
soft voices.
1. Press
until VOX/iVOX and the level setting (1-3) appear on the
display.
2. Press
or
to select the sensitivity level.
3. Press
to set or
to continue set up.
3 = High Sensitivity for quiet environments
2 = Medium Sensitivity for most environments
1 = Low Sensitivity for noisy environments
Note: When you connect a headset, the radio is automatically set to the
last chosen sensitivity level.
Q
Noise Filtering
T
The Q
noise-filtering feature helps to ensure uninterrupted communication
T
with other Motorola radios that have this feature. This feature also filters
out unwanted transmissions from other radios. This is useful in places
where there is heavy radio traffic, such as amusement parks or ski
resorts.
Note: Q
noise filtering is not available when the radio is scanning.
T
To turn Q
noise filtering on or off:
T
1. Press
until displays
. The current setting On/Off will flash.
2. Press
or
to turn noise filtering On or Off.
3. Press
to confirm your selection or
to continue set up.
To transmit to a radio that has Q
noise filtering turned on:
T
1. Select the same channel and Interference Eliminator Code as the other
radio.
2. Press
to send a call tone. This allows your voice to pass through
the Q
noise filter on the receiving radio.
T
3. Press
and speak normally.
Note: If you skip step 2, the beginning of your message may not be heard
on the receiving radio. For a 30-second period, starting after the last
transmission, all transmissions received on the selected channel and code
will pass through the Q
noise filter.
T
Keypad Tones
You may enable or disable the speaker key tones. You will hear the key
tone each time a button is pushed.
1. Press
until
appears. The current setting On/Off will flash.
2. Press either
or
to turn On or Off.
3. Press
to confirm or
to continue set up.
Note: When the key tone feature is off, the following are not disabled:
• Transmit timeout alert tone
• Call tone
• Low battery alert tone or
• The transmitted talk confirmation tone
Transmitting a Talk Confirmation Tone
You can set your radio to transmit a unique tone when you finish
transmitting. It is like saying "Roger" or "Over" to let others know you are
finished talking.
1. With the radio on, press
until the
appears. The current setting
On/Off flashes.
2. Press
or
to turn On or Off.
3. Press
to set or
to quit menu mode.
Special Features
Emergency Alert Mode
The Emergency Alert function can be used to signal others in your group
of your need for immediate help. All radios in your group using the same
channel and interference eliminator code can receive the message.
EM1003SR radios will automatically advance the speaker volume to a loud
setting (the maximum rated output level), regardless of the volume control
position. A unique alert tone will be emitted from the receiving radios and
heard by your group. The alert tone is also emitted from your own radio
speaker to attract attention in your vicinity. Any spoken words or
incidental sounds will be transmitted to others. EM1003SR radios will be
operating in an automatic "hands free" emergency transmission control
mode for a total of 30 seconds. For the duration of the emergency alert,
your radio will be locked into a transmitting mode and the other EM1003SR
in your group will be locked into a receiving mode to help ensure the receipt
of your emergency message.
1. Press and hold the Emergency Alert button for 3 seconds.
2. An alert signal will be transmitted for 8 seconds to alert other receivers.
3. Your voice or incidental sounds will be transmitted for 22 seconds.
There is no need to continue to hold the Emergency Alert button or use
the PTT button for your message to be transmitted.
4. After 30 seconds your radio will return to normal two-way mode.
EM1003SR radios will automatically return to the initial volume setting
as controlled by the volume knob. Both the sender and the receiver will
again be able to talk to each other using the PTT or VOX methods of
transmission control.
Note: EM1003SR radio can receive the emergency alert signal but will not
respond with adjusted volume steeings, controlled transmission mode or
unique alert tone. Users of other radio will hear a steady 8 second tone and
the 22 second voice transmissio.
Warning: The Emergency Alert feature should only be used in the event of
an actual emergency. Motorola is not responsible if there is no response to
the emergency alert from the receiving group.
Built-in Flashlight
Press the flashlight button to turn the light on. The switch functions as a
momentary control for the light.
Note: Turn off the flashlight when not in use to conserve battery power.
Keypad Lock
To avoid accidentally changing your radio settings:
1. Press
and hold until
displays.
2. When in lock mode, you can turn the radio on and off, adjust the volume,
receive, transmit, send a call tone, and monitor channels. All other
functions are locked.
To unlock the radio, press and hold
until
is no longer displayed.
Scanning Channels
Use scan to search the 8 channels for transmissions from unknown parties,
to find someone in your group who has accidentally changed channels, or to
quickly find unused channels for your own use.
There is a priority feature and 2 modes of scanning ( basic and advanced )
to make your search more effective. The basic scan mode uses the channel
and code combinations for each of the 8 channels as you have set them ( or
with the default code value of 1). The "Advanced Scan" mode will scan all
channels for any and all codes, detect any code in use, and use that code
value temporarily for that channel.
Priority is given to the "home channel," that is, the channel (and
Interference Eliminator Code) your radio is set to when you start the scan.
This means the initial channel (and code setting) is scanned more often than
the other 7 channels, and your radio will respond quickly to any activity
occurring on the home channel
as a priority.
To start Scanning:
1. Briefly press the
key. The scan
will appear in the display, and the
radio will begin to scroll through the channel and code combinations.
2. When the radio detects channel activity matching the channel and code
combination, it stops scrolling and you can hear the transmission.
3. To respond and talk to the person transmitting, press
within five
seconds after the end of the transmission.
4. The radio will resume scrolling through the channels five seconds after
the end of any received activity.
5. To stop scanning, briefly press the
key.
To start Advanced Scanning:
1. Set the Interference Eliminator Code to "zero" or OFF.
2. Briefly press the
key. The scan
will appear in the display, and the
radio will begin to scroll through the channels. No Interference Eliminator
Codes will filter what is heard.
3. When the radio detects channel activity with ANY code (or NO code), it
stops scrolling and you can hear the transmission. Any Interference
Eliminator Code that may be in use by that party will be detected and
displayed.
4. To respond and talk to the person transmitting, press
within five
seconds of the end of the transmission. The radio will transmit using the
newly detected Interference Eliminator Code.
5. The radio will resume scrolling through the channels five seconds after
the end of any received activity.
6. To stop scanning, briefly press the
key.
Scanning Notes:
1. If you press
while the radio is scrolling through inactive channels,
the transmission will be on the "home channel". Scanning will resume
five seconds after the end of your transmission. You may press the
key to stop scanning at any time.
2. If the radio stops on an undesired transmission, you may immediately
resume the scan by briefly pressing
or
.
3. If the radio repeatedly stops on an undesired transmission, you may
temporarily remove that channel from the scan list by pressing and
holding
or
for three seconds. You may remove more than one
channel in this way.
4. To restore the removed channel(s) to the scan list, turn the radio off and
then back on, or exit and re-enter the scanning mode by pressing
.
5. You cannot remove the home channel from the scan list.
6. In Advanced Scan, the detected code will only be used for one
transmission. You must note the code, exit scan, and set that detected
code on that channel to permanently use the detected code.
Warranty
Consumer Two-Way Radio Products and Accessories purchased in
Singapore.
What Does this Warranty Cover?
This Limited Warranty is a consumer's exclusive remedy, and applies as follows
to new Motorola branded products, accessories and software manufactured,
distributed and sold by Giant Telecom Ltd. Alcom is the local distributor in
Singapore, and warrants Motorola Two-Way Radio Products and Accessories
(collectively "Equipment') purchased in Singapore against defects in material and
workmanship under normal use and service, for the following periods of time:
Proof of Purchase: You are required to provide proof of purchase as a condition
of receiving warranty services. You are entitled to a replacement or repair
according to the terms and conditions of this Limited Warranty if your product is
found to be faulty within the Warranty Period. This Limited Warranty extends to
the original purchaser only and is not transferable.
Channels and Frequencies
Channel
Frequency(MHz)
1
446.00625 MHz
2
446.01875 MHz
3
446.03125 MHz
4
446.04375 MHz
5
446.05625 MHz
6
446.06875 MHz
7
446.08125 MHz
8
446.09375 MHz
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Dispose of batteries according to local regulations. Do not dispose as
household waste.
Products Covered
Warranty Period
Equipment as defined above, unless
One (1) year from the date of purchase
otherwise provided for below.
by the original consumer purchaser of
the Equipment unless otherwise provided
for below.
1. Decorative Accessories and
1. Limited lifetime warranty for the
Cases. Decorative covers, bezels,
lifetime of ownership by the original
PhoneWrap covers and cases.
consumer purchaser of the decorative
accessory or case.
2. Consumer Two-Way Radio
2. Thirty (30) days from the date of
Accessories.
purchase by the original consumer
purchaser of the two-way radio
accessory.
3. Products and Accessories that
3. The balance of the original warranty
are Repaired or Replaced.
or for thirty (30) days from the date
the products or accessories are
returned to the consumer, whichever
period is longer.
Who is covered?
This Limited Warranty applies only to the original consumer purchaser of the
Equipment, and is not transferable.
What will Alcom Electronics do?
Alcom Electronics, at its option, will at no charge either repair, or replace any
defective Equipment during the applicable Warranty Period. Alcom Electronics
may use functionally equivalent, reconditioned, refurbished, pre-owned or new
Equipment or parts at its discretion. No data, software or applications added to
Equipment, including but not limited to personal contacts, games and ringer
tones, will be reinstalled. To avoid losing such data, software and applications,
customers are advised to create a back up prior to requesting service.
How do we obtain Warranty Service or Other Information?
To obtain warranty service or information, please call:
Singapore
Alcom Electronics Pte Ltd.
Hotline:(65) 6841 2668
FAX: (65)6841 2628
You will receive instructions on how to ship the Equipment, at your expense, to
an authorized repair centre. To obtain warranty service, you must provide Alcom
Electronics with: (a) a copy of your purchase receipt, bill of sale or other
comparable proof of purchase for the Equipment; (b) a written description of
the problem; (c) the name and location of the installation facility (if applicable)
and (e) your postal address and contact telephone number. Alcom Electronics
will be the sole determinant as to whether the Equipment is defective.
Patent and Copyright Information
Manufactured, distributed or sold by Giant Telecom Ltd., official licensee
for this product. MOTOROLA, MOTOROLA SOLUTIONS and the Stylized M
Logo are trademarks or registered trademarks of Motorola Trademark
Holdings, LLC and are used under license. All other trademarks are the
property of their respective owners. ©2013 Motorola Solutions, Inc. All
rights reserved.
Exclusions
Normal Wear and Tear. Periodic maintenance, and repair and replacement of
parts due to normal wear and tear, are not covered by this Limited Warranty.
Batteries. Motorola supplied batteries will be replaced free of charge within the
first six (6) months of the date of purchase of the Equipment if the capacity of the
batteries falls below 80% of their rated capacity, or if the batteries develop a leak.
Abuse & Misuse. Defects or damage that result from: (a) improper operation,
storage, misuse or abuse, accident or neglect, such as physical damage (cracks,
scratches, etc.) to the surface of the Equipment resulting from misuse; (b) contact
with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the
like, extreme heat, or food; (c) use of the Equipment for commercial purposes or
subjecting the Equipment to abnormal usage or conditions; or (d) other acts which
are not the fault of Motorola Solutions Inc., or Giant Telecom Ltd., or Alcom
Electronics Pte Ltd., are not covered by this Limited Warranty.
Use of Non-Motorola branded Products and Accessories. Defects or damage
that result from the use of non-Motorola branded or certified products,
accessories, software or other peripheral equipment are not covered by this Limited
Warranty.
Unauthorized Service or Modification. Defects or damages resulting from
service, testing, adjustment, installation, maintenance, alteration, or modification
in any way by someone other than Motorola Solutions Inc., or Giant Telecom Ltd.,
Alcom Electronics Pte Ltd. or their authorized service centres, are not covered by
this Limited Warranty.
Altered Equipment. Equipment with (a) serial numbers or date tags that have
been removed, altered or obliterated; (b) broken seals or seals that show evidence
of tampering; (c) mismatched board serial numbers; or (d) nonconforming or
non-Motorola branded housings, or parts, are not covered by this Limited Warranty.
Communication Services. Defects, damage, or failure of the Equipment due to
any communication service or signal you may subscribe to or use with the
Equipment are not covered by this Limited Warranty.
Equipment Purchased Outside of Singapore. This Limited Warranty does not
extend to any Equipment which was purchased outside of Singapore.
What Other Limitations Are There?
TO THE EXTENT PERMITTED BY LAW, ALL CONDITIONS, WARRANTIES AND
TERMS NOT EXPRESSLY CONTAINED IN THIS LIMITED WARRANTY ARE
EXCLUDED.
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS LIMITED
WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL MOTOROLA
SOLUTIONS, INC., GIANT TELECOM LTD., OR ALCOM ELECTRONICS PTE LTD.
BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE EQUIPMENT, OR
ANY SOFTWARE, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR
PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, SOFTWARE
OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE ABILITY OR INABILITY TO USE THE EQUIPMENT, OR
ANY SOFTWARE, TO THE FULL EXTENT THESE DAMAGES MAY BE
DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the length of an implied
warranty, so the above limitations or exclusions may not apply to you. This
Limited Warranty gives you specific legal rights, and you may also have other
rights that vary from state to state or from one jurisdiction to another.
EM1003SR