Dimplex BCH20 Bach Gebruikershandleiding - Pagina 5
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Dimplex BCH20 Bach. Dimplex BCH20 Bach 5 pagina's. Wall fire
Pagina afdrukken
Controls - see Fig. 2
Three switches provide a choice of heat settings. The appliance is in
standby mode when the mains lead is plugged in. This is indicated by
the red neon behind the flame effect screen. The two selector switches
are in the ON position when the side with the markings on (i.e. I, or II)
are pushed in.
Push button switch 1
Controls the electricity supply to the heater
and flame effect. Press for 'ON' and
'Standby'. If both selector switches 2 and
3 are in the OFF position, the product
works on flame effect only.
Selector switch 2 (I)
Provides 1kW heat output
Selector switch 3 (II)
Provides 2kW output with switch 2
Thermostat (T) - see Fig. 2
In order to maintain a certain room temperature, set the
controller to 'max.'. Operate the appliance at full power until the
required room temperature is reached. Set back the
thermostatic controller until the appliance switches off with an
audible 'click'. This temperature will be kept almost constant
by the thermostatic control switching on and off automatically.
Please note that the appliance can only be switched on when
the thermostat setting is higher then the room temperature.
Remote control - see Fig. 7
The maximum range of use is ~ 15metres.
Warning: It takes time for the receiver to respond to the
transmitter.
Do not press the buttons more than once within two seconds
for correct operation.
Battery information - see Fig. 7
1.
Slide open the battery cover on the back of the remote
control
2.
Install AAA batteries into the remote control
3.
Replace the battery cover.
Discard leaky batteries
Dispose of batteries in the proper manner according to
provincial and local regulations.
Any battery may leak electrolyte if mixed with a different battery
type, if inserted incorrectly, if all the batteries are not replaced at
the same time, if disposed of in a fire, or if an attempt is made
to charge a battery not intended to be recharged.
Thermal Safety Cut-out
A thermal safety cut-out is incorporated in the heater to prevent
damage due to overheating. This can happen if the heat outlet
was restricted in any way. The heater will switch on once the
obstruction has been removed and the heater has cooled. If
the cut-out continues to operate intermittently, the heater should
be switched off and a service agent contacted.
Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
[c] Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex UK Limited.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.
Lamp Replacement - see Fig. 3, Fig. 4 and Fig. 5
Remove front cover.
Using a coin edge or screwdriver turn catch 1/4 turn clockwise
Pull the tray forward, the bulbs can now be replace with a 60W
E14 SES Clear Candle lamp.
Take care not to over-tighten the lamp
Trim colour options – see Fig. 6
The fire comes with a reversible trim.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use
abrasive cleaners. The glass viewing screen should be
cleaned carefully with a soft cloth. DO NOT use proprietary
glass cleaners.
To remove any accumulation of dust or fluff the soft brush
attachment of a vacuum cleaner should occasionally be used
to clean the outlet grille of the fan heater.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it
should not be disposed of with household waste.
Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice in your
country.
After Sales Service
Your product is guaranteed for one year from the date of
purchase.
Within this period, we undertake to repair or exchange this
product free of charge (excluding lamps & subject to availability)
provided it has been installed and operated in accordance
with these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact our
customer services help desk on 0845 600 5111. It would assist
us if you can quote the model number, series, date of purchase,
and nature of the fault at the time of your call. The customer
services help desk will also be able to advise you should you
need to purchase any spares.
Please do not return a faulty product to us in the first instance
as this may result in loss or damage and delay in providing you
with a satisfactory service.
Please retain your receipt as proof of purchase.