Toshiba 24S3KS-M Gebruikershandleiding - Pagina 4

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Toshiba 24S3KS-M. Toshiba 24S3KS-M 12 pagina's. For general public use

Pagina afdrukken

PRESET OPERATION

Set your preferred operation for future use. The setting will be memorized by the

unit for future operation (except airflow direction).

1. Select your preferred operation.

2. Press and hold

The P mark displays.

3. Press

: Operate the preset operation.

AUTO RESTART OPERATION

This product is designed so that, after a power failure, it can restart automatically

in the same operating mode as before the power failure.

Information

The product was shipped with Auto Restart function in the ON position.

Turn it OFF if this function is not required.

How to cancel the Auto Restart

1. Press and hold the [RESET] button on the indoor unit for 3 seconds to

cancel the operation. (3 beeps will sound but OPERATION lamp does not

blink)

2. Press and hold the [RESET] button on the indoor unit for 3 seconds to set

the operation. (3 beeps will sound and OPERATION lamp blink 5 time/sec

for 5 seconds)

• Do not operate ON timer and OFF timer.

Note: Default setting of auto restart operation is ON.

QUIET OPERATION

To operate at super low fan speed for quiet operation (except in DRY mode)

Press

QUIET

: Start and stop the operation.

Note: Under certain conditions, QUIET operation may not provide adequate

cooling due to low sound features.

COMFORT SLEEP OPERATION

For comfortable sleep, automatically control air flow and automatically turn OFF.

Press

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note: The cooling operation, the set temperature will increase automatically

1 degree/hour for 2 hours (maximum 2 degrees increase).

MAINTENANCE

Firstly, turn off the circuit breaker.

Filter Reset (Some models only)

FILTER lamp lights on; the filter must be cleaned.

To turn off the lamp, push the RESET button on the indoor unit or the FILTER

button on the remote control.

Indoor Unit and Remote Control

• Clean the indoor unit and the remote control with a wet cloth when needed.

• No benzine, thinner, polishing powder or chemically-treated duster.

SELF CLEANING OPERATION (COOL AND

DRY OPERATION ONLY)

To protect bad smell caused by the humidity in the indoor unit.

1. If the

button is pressed once during "Cool" or "Dry" mode,

the fan will continue to run for other 20 minutes, then it will turn off

automatically. This will reduce the moisture in the indoor unit.

2. To stop the unit immediately, press the

30 seconds.

TSB 1110655137_EN.indd 3

for 3 seconds to memorize the setting.

more 2 times within

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being activated

for 3 minutes when suddenly restarted or switched to ON.

2. Some minor cracking sound may occur when unit operating. This is normal

because the cracking sound may be caused by expansion/contraction of

plastic.

Air conditioner operating conditions

Temp.

Outdoor Temperature

Operation

Cooling

21°C ~ 43°C

Dry

19°C ~ 43°C

TROUBLESHOOTING (CHECK POINT)

The unit does not operate.

• The power main switch is turned

off.

• The circuit breaker is activated to

cut off the power supply.

• Stoppage of electric current.

• ON timer is set.

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air

conditioners are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold

button on the Remote Control by the tip of the pencil.

"00" will be shown on the display.

4. Press

during pushing

will disappear and the air conditioner will turn OFF. The Remote Control B

is memorized.

Note: 1. Repeat above step to reset Remote Control to be A.

2. Remote Control A has not "A" display.

3. Default setting of Remote Control from

factory is A.

Room Temperature

21°C ~ 32°C

17°C ~ 32°C

Cooling is abnormally low.

• The filters are blocked with dust.

• The temperature has been set

improperly.

• The windows or doors are opened.

• The air inlet or outlet of the outdoor

unit is blocked.

• The fan speed is too low.

• The operation mode is FAN or DRY.

. "B" will show on the display and "00"

12/18/57 BE 1:42 PM