Toshiba 14AF45C, 20AF45C Servicehandleiding - Pagina 20
Blader online of download pdf Servicehandleiding voor {categorie_naam} Toshiba 14AF45C, 20AF45C. Toshiba 14AF45C, 20AF45C 50 pagina's. Fst pure colorstream
Ook voor Toshiba 14AF45C, 20AF45C: Gebruikershandleiding (28 pagina's)
Pagina afdrukken
2-6: VERTICAL POSITION
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Adjust the VR401 until the horizontal line becomes fit to
the notch of the shadow mask. (Refer to Fig. 2-1)
2-7: VERTICAL SIZE
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V. SIZE".
4.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside
and downside becomes 9 ± 2%.
2-8: VERTICAL LINEARITY
NOTE: Adjust after performing adjustments in section 2-7.
After the adjustment of Vertical Linearity, reconfirm
the Vertical Position and Vertical Size adjustments.
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness, contrast,
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (08) on the remote control to
select "V. LIN".
4.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside
and downside becomes minimum.
2-9: LEVEL
1.
Connect the AC voltmeter to pin 6 of CP101.
2.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (33) on the remote control to
select "LEVEL".
3.
Press the VOL. UP/DOWN button on the remote control
until the AC voltmeter is 75 ± 2mV.
ELECTRICAL ADJUSTMENTS
horizontal line
Notch
Shadow mask
Fig. 2-1
2-10: SEPARATION 1, 2
Please do the method (1) or method (2) adjustment.
Method (1)
1.
Set the multi-sound signal generator for each different L-
ch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz) and
receive the RF.
2.
Connect the oscilloscope to the Audio Out Jack.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (34) on the remote control to
select "SEP 1".
4.
Press the VOL. UP/DOWN button on the remote control to
adjust it until the audio output wave becomes a fine sine
wave.
5.
Press the CH UP button once the set to "SEP 2" mode.
Then perform the above adjustment 4.
Method (2)
1.
Set the multi-sound signal generator L-ch=1KHz, R-ch
=Non input and receive the RF.
2.
Connect the oscilloscope to the Audio Out Jack (R-ch).
3.
Press the AUDIO SELECT button on the remote control to
set to the stereo mode.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (34) on the remote control to
select "SEP 1".
5.
Press the VOL. UP/DOWN button on the remote control to
adjust it until the R-ch output becomes minimum.
6.
Set the multi-sound signal generator L-ch=Non input,
R-ch=1KHz and receive the RF.
7.
Connect the oscilloscope to the Audio Out Jack (L-ch).
8.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (35) on the remote control to
select "SEP 2".
9.
Press the VOL. UP/DOWN button on the remote control to
adjust it until the L-ch output becomes minimum.
The output difference of the between with Filter and
without Filter should be more than 25db for both L and R.
2-11: OSD POSITION
1.
Activate the adjustment mode display of Fig. 1-1.
2.
Press the VOL. UP/DOWN button on the remote
control until the difference of A and B becomes
minimum. (Refer to Fig. 2-2)
00 OSD
A
D-2
TV
36
B
Fig. 2-2
14AF45/14AF45C