Toshiba 20AF46C Servicehandleiding - Pagina 20

Blader online of download pdf Servicehandleiding voor {categorie_naam} Toshiba 20AF46C. Toshiba 20AF46C 50 pagina's. Fstpure colorstream color television
Ook voor Toshiba 20AF46C: Gebruikershandleiding (28 pagina's)

Pagina afdrukken
Toshiba 20AF46C Servicehandleiding

1. ADJUSTMENT PROCEDURE

Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
Use an isolation transformer when performing any
•
service on this chassis.
Before removing the anode cap, discharge electricity
•
because it contains high voltage.
When removing a PCB or related component, after
•
unfastening or changing a wire, be sure to put the wire
back in its original position.
When you exchange IC and Transistor for a heat sink,
•
apply the silicon grease on the contact section of the
heat sink. Befor applying new silicon grease, remove
all the old silicon grease. (Old grease may cause
damages to the IC and Transistor.)
Prepare the following measurement tools for electrical
adjustments.
1. Oscilloscope
2. Digital Voltmeter
3. Multi-sound Generator
4. Pattern Generator
On-Screen Display Adjustment
1. In the condition of NO indication on the screen.
Press the VOL. DOWN button on the set and the
Channel button (9) on the remote control for more than 1
second to appear the adjustment mode on the screen as
shown in Fig. 1-1.
00 OSD
2.
Use the Channel UP/DOWN button or Channel button
(0-9) on the remote control to select the options shown
in Fig. 1-2.
3.
Press the MENU button on the remote control to end the
adjustments.
NO.
FUNCTION
00
OSD H
01
CUT OFF
02
H. VCO
03
H. PHASE
04
AFC GAIN
05
V. SHIFT
06
H. SIZE
07
V. SIZE
08
V. LINERITY
09
VS CORRECTION
10
R DRIVE
11
B DRIVE
12
R CUT OFF
13
G CUT OFF
14
B CUT OFF
15
BRIGHT MAX
16
BRIGHT CENT
17
BRIGHT MIN

ELECTRICAL ADJUSTMENTS

TV
29
Fig. 1-1
NO.
FUNCTION
18
CONTRAST MAX
19
CONTRAST CENT
20
CONTRAST MIN
21
COLOR MAX
22
COLOR CENTER
23
COLOR MIN
24
TINT
25
SHARPNESS
26
CB DL
27
CR DL
28
CB PED
29
CR PED
30
PARABOLA
31
CORNER
32
TRAPWZIUM
33
LEVEL
34
SEPARATION1
35
SEPARATION2
Fig. 1-2

2. BASIC ADJUSTMENTS

2-1: CONSTANT VOLTAGE
1.
Set condition is AV MODE without signal.
2.
Connect the digital voltmeter to the TP003.
Adjust the VR502 until the digital voltmeter is 115 ± 0.5V.
3.
2-2: CUT OFF
1.
Place the set with Aging Test for more than 15 minutes.
2.
Set condition is AV MODE without signal.
3.
Using the remote control, set the brightness and
contrast to normal position.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "CUT OFF".
5.
Adjust the Screen Volume until a dim raster is obtained.
2-3: WHITE BALANCE, WHITE BALANCE CS
NOTE: Adjust after performing CUT OFF adjustment.
1.
Place the set with Aging Test for more than 15 minutes.
2.
Receive the gray scale pattern from the Pattern Generator
with Brust On.
3.
Using the remote control, set the brightness and contrast
to normal position.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (12) on the remote control to
select "R. BIAS".
5.
Press the CH. UP/DOWN button on the remote control to
select the "R. BIAS", "G. BIAS", "B. BIAS", "B. DRIVE" or
"R. DRIVE".
6.
Adjust the VOL. UP/DOWN button on the remote control
to whiten the R. BIAS, G. BIAS, B. BIAS, B. DRIVE and
R. DRIVE at each step tone sections equally.
7.
Perform the above adjustments 5 and 6 until the white
color is looked like a white.
8.
Press the TV/VIDEO button on the remote control to set
to the CS mode.
9.
Receive the gray scale pattern from the Pattern Generat
or with Brust On.
10.
If the picture is too much green.Activate the adjustment
mode display of Fig. 1-1 and press the channel button
(28) on the remote control to select "CB PED".
11.
Adjust the VOL. UP/DOWN button on the remote control
to select the step up.
12.
If the picture is too much red.Activate the adjustment
mode display of Fig. 1-1 and press the channel button
(29) on the remote control to select "CR PED".
13.
Adjust the VOL. UP/DOWN button on the remote control
to select the step down.
2-4: FOCUS
1.
Receive the monoscope pattern.
2.
Turn the Focus Volume fully counterclockwise once.
3.
Adjust the Focus Volume until picture is distinct.
D-1
20AF46/20AF46C