Toshiba TDP-EX21 Gebruikershandleiding - Pagina 22

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Toshiba TDP-EX21. Toshiba TDP-EX21 29 pagina's.

Pagina afdrukken
Toshiba TDP-EX21 Gebruikershandleiding
Using the menus (Continued)
Default setting 2 menu
Item
Projection
Sets projection mode in accordance with Placement Style.
mode
(Standard)
Fan mode
Sets the cooling fan speed.
Remote control * This function is not available. Please do not use.
Key lock
Lock the control panel buttons.
[
or
: Enter setting]
[
:Select OK to end
Press [Cancel] to return.
Lamp power
Sets the lamp power.
Reset all
Press
. (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password
Password setting
p.33
Press
.
Password registration/Password setting
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
increases.) Set this option to use the projector at high altitude (over 1,500 meters
above sea level).
•
Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Remote code for the supplied remote control is set to [1] by default. Since setting the code
to [2] will cause the remote control to become inoperable, always set the code to [1].
[Key lock]
Avoid operating errors by locking the projector's control panel buttons. (The remote
control operations are still available.)
Control panel operations are locked after the setting is done, and operations using the
control panel buttons are disabled.
•
To release the key lock, set the [Key lock] to [Off] using the remote control. You can
also set the [Key lock] to [Off] by pressing the [RETURN] button on the projector
for 10 seconds. (When operating the main unit, the LAMP and TEMP indicators will
glow orange for 3 seconds, and the projector will beep.)
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.
Description
p.20
(Rear)
(Ceiling)
Standard
[
: Select On/Off
]
[
: Confirm]
]
Low
Standard
Yes
42

Displaying Information (Status display)

■
This displays information about the input signal, lamp use time, etc.
Item
(Rear ceiling)
Input
High
Mode name
Resolution
Frequency
Sync
Signal format
Video mode
Lamp time
Lamp reset count The count for lamp replacement
No
Total time
Version
Notes
1:
The mode of supported RGB signals
2:
Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3:
Displays [Lamp time] as an estimated measure of when the lamp should be replaced.
(Cannot be used as a counter of guaranteed lamp time.) When the displayed time
approaches 2,000 hours, consult with a dealer about getting a replacement for:
TLPLW15 for TDP-EX21 (sold separately).
4:
[Version] shows the version of the projector's internal control program. This firmware
version will be requested for customer service purposes.
Note
•
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
Description
Computer
Input source name
Yes
[Note 1]
RGB input mode
Yes
Resolution (in dots)
Yes
Sync frequency
Yes
[Note 2]
Sync signal polarity
Yes
Y/P
/P
signal format
No
B
R
Color method of video signal
No
[Note 3]
Time of lamp use
Yes
Yes
The total time that this projector is
Yes
used.
[Note 4]
Firmware version
Yes
p.53
is shown.
43
"Yes": displayed, "No": not displayed
Y/P
/P
Video
S-video
B
R
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes