Dimplex AC3CN Instructies - Pagina 4

Blader online of download pdf Instructies voor {categorie_naam} Dimplex AC3CN. Dimplex AC3CN 4 pagina's. Recessed ceiling heater/ over door heater
Ook voor Dimplex AC3CN: Gebruikershandleiding (4 pagina's), Gebruikershandleiding (8 pagina's)

Pagina afdrukken

Installation of Switch Panel

WARNING: The Switch Panel should not be installed in a toilet or

washroom.

The backing box (standard B.S. double gang as shown in Fig. 3) should

be rebated into a suitable wall. The box should be fitted so that the

switch panel will be flush with the wall. Suitable conduit should be used

where applicable to carry the cable between the heater and the switch

panel.

The cable used to connect the heater to the switch panel should have

sufficient cores to allow connection as per the enclosed wiring diagrams.

Operation of Switch Panel

Switch on electrical supply (MAINS IN) to the Switch Panel.

Switching the switch marked 'I' (see '1' in Fig. 3) energises the fan and

switches on the electrical supply to the heater.

The heat selection switches allow heat settings to be chosen as shown

below:

Settings -

I +

The desired setting can be obtained through switch selection.

Maintenance

WARNING: ALWAYS DISCONNECT HEATER FROM THE POWER

SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.

Thermal Safety cut-out(s)

The power supply to the heating elements will be interrupted if one or a

combination of the following abnormal events occur:

Air inlet/outlet panel is obstructed.

Internal ventilation is impaired due to build up of dust

and fluff.

Blower unit stalls.

Note : If the cut-out operates, the fan may continue to run impairing the

performance of the heater. The heater must be turned off immediately

and the cut-out(s) reset following the 'Procedure for resetting cut-out(s)'.

Procedure for resetting cut-out(s)

Establish cause and eliminate.

You need to reset thermal cut-out(s), located behind the Air Inlet/Outlet

panel (see 'B' in Fig. 5 and for detail view see Fig. 6).

To access the Air Inlet/Outlet panel of the heater you must remove the

grille core out from it's frame, by first lifting up and then sliding to one

side - see steps 1 & 2 in Fig. 5.

To reset the thermal safety cut-out, press the black reset button (see 'g'

in Fig. 6) on the side of the cut-out (see 'f' in Fig. 6) as described in

steps 2 - 4 :-

Glen Dimplex UK Limited

Millbrook House

Grange Drive

Hedge End

Southampton

Hampshire. SO30 2DF

England

Dimpco Ltd.

Airport Road

Cloghran

Co. Dublin

Republic of Ireland

[c] Glen Dimplex UK Limited

Fan Only

Heat

Full Heat

Customer Services:

(8am – 6pm Mon-Fri

8.30am – 1pm Sat)

Customer Services:

Steps to reset cut-out(s)

Disconnect power supply.

Pass small flat head screwdriver through Air Inlet/Outlet panel

'B' to button side of cut-out (see 'g' in Fig. 6) avoiding contact

with element (see 'e' in Fig. 6).

Press reset button in direction shown in Fig. 6 to reset cut-out.

(Cut-out clicks when reset)

Remove screwdriver carefully.

Turn on supply.

If the cut-out continues to operate intermittently, the heater should be

switched off and a service agent contacted.

Cleaning of Heater / Switch Panel

Internal and grille appearance can be maintained by occasionally

vacuuming or wiping with a light duster. External appearance of the

Switch Panel can be maintained by wiping occasionally with a light duster

or for stain removal, a weak soap solution can be applied with a cloth

and the surface wiped dry.

Note: Care must be taken to avoid any moisture ingress into the

switch panel.

After Sales Service

Your product is guaranteed for one year from the date of purchase.

Within this period, we undertake to repair or exchange this product free

of charge provided it has been installed and operated in accordance

with these instructions.

Your rights under this guarantee are additional to your statutory rights,

which in turn are not affected by this guarantee.

Should you require after sales service you should contact our customer

services help desk on 0870 727 0101. It would assist us if you can

quote the model number, series, date of purchase, and nature of the

fault at the time of your call. The customer services help desk will also

be able to advise you should you need to purchase any spares.

Please do not return a faulty product to us in the first instance as this

may result in loss or damage and delay in providing you with a satisfactory

service.

Please retain your receipt as proof of purchase.

Tel. +44 (0) 870 7270101

Fax. +44 (0) 870 7270102

e-mail - [email protected]

Tel. +353 (0) 1 842 4833

Fax. +353 (0) 1 842 4839