Dimplex SP420 Gebruikershandleiding - Pagina 6

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Dimplex SP420. Dimplex SP420 8 pagina's. Dimplex wall fires installation and operating instructions
Ook voor Dimplex SP420: Gebruikershandleiding (8 pagina's), Handleiding voor installatie en gebruik (9 pagina's), Handleiding voor installatie en gebruik (8 pagina's)

Pagina afdrukken

Lamp Replacement – SP520, SP15, SP920 &

SP19

WARNING – ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE REMOVING LAMPS.

Warning - The lamps reach high temperatures during

operation. For this reason, allow the lamps to cool down

after switching off the appliance.

The front panel will need to be removed in order to change

lamps (SP520 & SP15 see Fig. 10) and (SP920 & SP19 see

Fig. 11).

Warning - The front panel is heavy and easily damaged.

The front panel is supported at the top by the chassis and

held tight by magnets at the top and bottom on the SP520 &

SP15 model - see Fig. 10. On the SP920 & SP19 the front

panel is held at the bottom by a fixing screw - see Fig. 11.

SP520 & SP15

To gain access to lamps please apply the following

procedure:

While holding the front panel by its sides with both hands,

carefully tilt the bottom of the frame outwards until free and

then lift the panel up (1) and then away (2) from the main

body - see Fig. 10.

To gain access to the bulbs remove the screws at 'A' to remove

the cover bracket 'X' and the screws at 'B' to remove the

cover bracket 'Y' - see Fig. 10.

For access to the bottom bulbs, carefully slide the flexible

rotisserie (see 'a' in Fig. 12) to one side ensuring that the

rubber grommet is not lost (see 'b' in Fig. 12).

Remove the defective lamp by unscrewing it (see Fig. 12).

Replace with a 60W E14 SES Clear Candle bulb, rotating it.

Take care not to over-tighten the lamp.

Steps for reassembling the heater

Refit the rotisserie making sure that the rubber grommet

pushed into the slotted hole on the axial bracket.

Replace the cover brackets 'X' and 'Y' - see Fig. 10.

Replace the front by aligning the slots on the front frame

and making sure that it catches fully on the support

brackets.

The magnets on the chassis will hold the front flush to

the main body.

SP920 & SP19

To gain access to lamps please apply the following

procedure:

Remove the fixing screw (1) from the base of the front frame

while holding the front panel by its sides with both hands,

carefully tilt the bottom of the frame out-wards until free and

then lift the panel up (2) and then away (3) from the main

body – see Fig. 11.

To gain access to the bulbs remove the screws at 'A' to remove

the cover bracket 'X' - see Fig. 11.

To gain access to the lamps, using a coin edge or screw

driver turn catch ¼ turn anti-clock wise to unlock (see detail

in Fig. 13). Open the hinged door (take care not to lean or put

weight on the door as this will result in damaging it).

Remove the defective lamp by unscrewing it (see Fig. 13).

Replace with a 60W E14 SES clear candle bulb rotating it

take care not to over tighten the lamp.

Steps for reassembling the heater

Swing the door back in to position and turn the catch ¼ turn

clock wise to lock and replace bracket 'X' - see Fig. 11.

Replace the front by aligning the slots on the front frame and

making sure that it catches fully on the support brackets and

replace the fixing screw to the underside of the front frame.

Cleaning

WARNING – ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE CLEANING THE HEATER.

Recycling

For electrical products sold within the European Community.

At the end of the electrical products useful life it should not be

disposed of with household waste. Please recycle where

facilities exist. Check with your Local Authority or retailer for

recycling advice in your country.

After Sales Service

Your product is guaranteed for one year from the date of

purchase.

Within this period, we undertake to repair or exchange this

product free of charge (excluding lamps & subject to

availability) provided it has been installed and operated in

accordance with these instructions.

Your rights under this guarantee are additional to your statutory

rights, which in turn are not affected by this guarantee.

Should you require after sales information or assistance

with this product please go to www.dimplex.co.uk wher

you will find our self help guide by clicking on "After Sales"

or ring our helpdesk on 0845 600 5111 (UK) or 01 842 4833

(R.O.I.) .

carefully

Spare parts are also available on the website

www.dimplex.co.uk

Please retain your receipt as proof of purchase.

For general cleaning use a soft clean duster –

never use abrasive cleaners. The glass viewing

screen should be cleaned carefully with a soft

cloth. DO NOT use proprietary glass cleaners.