Pioneer AVH-P6800DVD - DVD Changer With LCD Monitor Installatiehandleiding - Pagina 4
Blader online of download pdf Installatiehandleiding voor {categorie_naam} Pioneer AVH-P6800DVD - DVD Changer With LCD Monitor. Pioneer AVH-P6800DVD - DVD Changer With LCD Monitor 8 pagina's. Owner's manual
Ook voor Pioneer AVH-P6800DVD - DVD Changer With LCD Monitor: Installatiehandleiding (9 pagina's), Gebruikershandleiding (34 pagina's)
Pagina afdrukken
Installation
When connecting the external video component and the display
This product
Audio 1 input
RCA cables (sold separately)
(AUDIO 1 INPUT)
To audio outputs
External video
component
(sold separately)
Video output
To video output
(VIDEO OUTPUT)
Video 1 input (VIDEO 1 INPUT)
RCA cables (sold separately)
Audio 2 input
(AUDIO 2 INPUT)
To audio outputs
External video
component
(sold separately)
To video output
Video 2 input
(VIDEO 2/BACK UP CAMERA INPUT)
Display with
RCA input jacks
RCA cable
To video input
(sold separately)
• It is necessary to set AV INPUT to VIDEO on the SETUP menu when connecting to
external video component.
• It is necessary to set AV INPUT to EXT-V on the SETUP menu when connecting to
DVD player.
When using a display connected to video output
This product's video output is for connection of a display to enable passengers in the rear
seats to watch the DVD or Video CD.
WARNING:
• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD
while Driving.
Note:
Installing the remote control unit
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
When not using the remote control unit,
up properly, and the unit and the system work
secure it with velcro tape to prevent it
properly.
from moving.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
• Thoroughly wipe off the surface
can cause malfunctions.
before affixing the velcro tape.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• Do not install the display where it may (i) obstruct
the driver's vision, (ii) impair the performance of
any of the vehicle's operating systems or safety
features, including air bags, hazard lamp buttons or
(iii) impair the driver's ability to safely operate the
vehicle.
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot
— for instance, near a heater outlet.
• If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 9)
Fig. 9
• The cords must not cover up the area shown in the
figure below. This is necessary to allow the ampli-
Fig. 8
fires to radiate freely. (Fig. 10)
Leave this space.
Fig. 10
Installation using the screw holes on the side of this unit
1. Remove the frame.
2. Fastening this unit to the factory radio mounting bracket.
Position this unit so that the brackets screw holes and its screw holes are aligned (are fitted),
and tighten the screws at 3 or 4 locations on each side. Use either the binding screws (5 × 6
mm) or flush surface screws (5 × 6 mm), depending on the shape of the bracket's screw
holes.
Remote control unit
Velcro tape (small)
(hard)
Velcro tape (small)
(soft)
Fig.11
Factory radio mounting bracket
If the pawl gets in the
way, bend it down
Binding screw or
flush surface screw
Be sure to use the
screws supplied
Dashboard or console
with this product.
Note:
• In some types of automobiles, descrepancy may occur between the main unit and the dashboard. If
this happens, use the supplied panel to fill the gap.
• To some types of automobiles, ths unit cannot be properly installed. In such case, use the installa-
tion kit ADT-VA133 (sold separately).
<ENGLISH>
Fig. 12
Fig. 13