Pioneer DEH-2100 Installatiehandleiding

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Pioneer DEH-2100. Pioneer DEH-2100 6 pagina's.

Pagina afdrukken

DEH-2100

DEH-1100

DEH-21

DEH-11

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit

est conforme à CEMA.

Los colores de los cables este producto se conforman

con el código de colores CEMA.

Printed in U.S.A.

Imprimé aux Etats-Unis

<HRD0147-A> UC

<99K00T0T01>

Connecting the Units

Note:

•

When this product's source is switched ON, a

control signal is output through the blue/white

•

This unit is for vehicles with a 12-volt battery

lead. Connect to an external power amp's system

and negative grounding. Before installing it in a

remote control or the car's Auto-antenna relay

recreational vehicle, truck, or bus, check the bat-

tery voltage.

control terminal. (Max. 300 mA 12 V DC.) If the

car features a glass antenna, connect to the anten-

•

To avoid shorts in the electrical system, be sure

to disconnect the ≠ battery cable before begin-

na booster power supply terminal.

ning installation.

•

When an external power amp is being used with

this system, be sure not to connect the blue/white

•

Refer to the owner's manual for details on con-

lead to the amp's power terminal. Likewise, do

necting the power amp and other units, then

not connect the blue/white lead to the power ter-

make connections correctly.

minal of the auto-antenna. Such connection could

•

Secure the wiring with cable clamps or adhesive

cause excessive current drain and malfunction.

tape. To protect the wiring, wrap adhesive tape

•

To avoid short-circuiting, cover the disconnected

around them where they lie against metal parts.

lead with insulating tape. Especially, insulate the

•

Route and secure all wiring so it cannot touch

unused speaker leads without fail. There is a pos-

any moving parts, such as the gear shift, hand-

sibility of short-circuiting if the leads are not

brake and seat rails. Do not route wiring in

insulated.

places that get hot, such as near the heater outlet.

•

If this unit is installed in a vehicle that does not

If the insulation of the wiring melts or gets torn,

have an ACC (accessory) position on the ignition

there is a danger of the wiring short-circuiting to

switch, the red lead of the unit should be con-

the vehicle body.

nected to a terminal coupled with ignition switch

•

Don't pass the yellow lead through a hole into

ON/OFF operations. If this is not done, the vehi-

the engine compartment to connect to the battery.

cle battery may be drained when you are away

This will damage the lead insulation and cause a

from the vehicle for several hours.

very dangerous short.

•

Do not shorten any leads. If you do, the protec-

tion circuit may fail to work when it should.

•

Never feed power to other equipment by cutting

the insulation of the power supply lead of the

unit and tapping into the lead. The current capac-

ity of the lead will be exceeded, causing over-

heating.

•

When replacing fuse, be sure to use only fuse of

the rating prescribed on this unit.

ACC position

No ACC position

•

Since a unique BPTL circuit is employed, never

•

The black lead is ground. Please ground this lead

wire so the speaker leads are directly grounded

separately from the ground of high-current prod-

or the left and right ≠ speaker leads are com-

ucts such as power amps.

mon.

If you ground the products together and the

•

Speakers connected to this unit must be high-

ground becomes detached, there is a risk of dam-

power types with minimum rating of 40 W

age to the products or fire.

(45 W)* and impedance of 4 to 8 ohms.

Connecting speakers with output and/or imped-

•

Cords for this product and those for other prod-

ance values other than those noted here may

ucts may be different colors even if they have the

result in the speakers catching fire, emitting

same function. When connecting this product to

smoke, or becoming damaged.

another product, refer to the supplied Installation

* DEH-2100 and DEH-21

manuals of both products and connect cords that

have the same function.

Connection Diagram

This Product

Rear output

Antenna jack

Black (ground)

To vehicle (metal) body.

Red

To electric terminal controlled by ignition

switch (12 V DC) ON/OFF.

Yellow

To terminal always supplied with power

regardless of ignition switch position.

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Perform these connections when using a different amp (sold separately).

Connecting cords with RCA

pin plugs (sold separately)

To system control terminal of

the power amp or Auto-antenna

Fuse

relay control terminal.

(Max. 300 mA 12 V DC.)

Blue/white

System remote control

Fuse holder

White

Gray

Front

speaker

White/black

Gray/black

≠

Right

Left

Green

Violet

Rear

speaker

Green/black

Violet/black

≠

Rear

speaker

≠

Power amp

(sold separately)