Pioneer DEH-2330R Installatiehandleiding - Pagina 3

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Pioneer DEH-2330R. Pioneer DEH-2330R 6 pagina's. High power cd player with rds tuner
Ook voor Pioneer DEH-2330R: Servicehandleiding (3 pagina's), Servicehandleiding (3 pagina's)

Pagina afdrukken

Pioneer DEH-2330R Installatiehandleiding

1. This product

Note:

2. Rear output

Depending on the kind of vehicle, the functio

of 3* and 5* may be different. In this case, be

sure to connect 2* to 5* and 4* to 3*.

3. Antenna jack

6. Connect leads of the

same color to each other.

7. Cap (1*)

When not using this terminal,

do not remove the cap.

8. Yellow (3*)

9. Yellow (2*)

Back-up

To terminal always supplied

(or accessory)

with power regardless of

ignition switch position.

10. Red (5*)

11. Red (4*)

Accessory

To electric terminal controlled

(or back-up)

by ignition switch (12 V DC)

ON/OFF.

12. Black (ground)

14.Speaker leads

To vehicle (metal) body.

White

: Front left +

White/black

: Front left ≠

Gray

: Front right +

Gray/black

: Front right ≠

Green

: Rear left +

Green/black

: Rear left ≠

Violet

: Rear right +

Violet/black

: Rear right ≠

13.ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to

connect to both connectors.

15. Connecting cords with

RCA pin plugs (sold separately).

4. Fuse

17. Yellow/black

If you use a cellular telephone, connect it via the Audio

Mute lead on the cellular telephone. If not, keep the Audio

Mute lead free of any connections.

19. System remote control

18. Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

20.Rear speaker (Left)

≠

22. Perform these connections when using

a different amp (sold separately).

23. Blue/white (6*)

24. Blue/white (7*)

To Auto-antenna relay control

terminal (max. 300 mA 12 V DC).

25.

The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control type. In another

type of vehicle, never connect 6* and 7*.

Connecting the Units

Note:

•

This unit is for vehicles with a 12-volt battery

and negative grounding. Before installing it in a

recreational vehicle, truck, or bus, check the bat-

16. Power amp

tery voltage.

(sold separately)

•

To avoid shorts in the electrical system, be sure

to disconnect the

≠ battery cable before begin-

ning installation.

•

Refer to the owner's manual for details on con-

necting the power amp and other units, then

make connections correctly.

•

Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

•

Route and secure all wiring so it cannot touch

any moving parts, such as the gear shift, hand-

brake and seat rails. Do not route wiring in

places that get hot, such as near the heater outlet.

If the insulation of the wiring melts or gets torn,

there is a danger of the wiring short-circuiting to

the vehicle body.

•

Don't pass the yellow lead through a hole into

the engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

21.Rear speaker (Right)

•

Do not shorten any leads. If you do, the protec-

tion circuit may fail to work when it should.

•

Never feed power to other equipment by cutting

≠

the insulation of the power supply lead of the

unit and tapping into the lead. The current capac-

ity of the lead will be exceeded, causing over-

heating.

•

When replacing fuse, be sure to use only fuse of

the rating prescribed on this unit.

•

Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded

or the left and right ≠ speaker leads are com-

mon.

•

Speakers connected to this unit must be high-

power types with minimum rating of 45 W (50

W)* and impedance of 4 to 8 ohms. Connecting

speakers with output and/or impedance values

other than those noted here may result in the

speakers catching fire, emitting smoke, or

becoming damaged.

*DEH-2330R, DEH-2300R and DEH-2300RB

Fig. 4

Abb. 4

Afb. 4

Connection Diagram (Fig. 4)

•

When this product's source is switched ON, a

control signal is output through the blue/white

1. This product

lead. Connect to an external power amp's system

2. Rear output

remote control or the car's Auto-antenna relay

3. Antenna jack

control terminal (max. 300 mA 12 V DC). If the

4. Fuse

car features a glass antenna, connect to the anten-

5. Note:

na booster power supply terminal.

Depending on the kind of vehicle, the function of

•

When an external power amp is being used with

3* and 5* may be different. In this case, be sure

this system, be sure not to connect the blue/white

to connect 2* to 5* and 4* to 3*.

lead to the amp's power terminal. Likewise, do

6. Connect leads of the same color to each other.

not connect the blue/white lead to the power ter-

7. Cap (1*)

minal of the auto-antenna. Such connection could

cause excessive current drain and malfunction.

When not using this terminal, do not remove the

•

To avoid short-circuiting, cover the disconnected

cap.

lead with insulating tape. Especially, insulate the

8. Yellow (3*)

unused speaker leads without fail. There is a pos-

Back-up (or accessory)

sibility of short-circuiting if the leads are not

9. Yellow (2*)

insulated.

To terminal always supplied with power regard-

•

If this unit is installed in a vehicle that does not

less of ignition switch position.

have an ACC (accessory) position on the ignition

10. Red (5*)

switch, the red lead of the unit should be con-

Accessory (or back-up)

nected to a terminal coupled with ignition switch

11. Red (4*)

ON/OFF operations. If this is not done, the vehi-

To electric terminal controlled by ignition switch

cle battery may be drained when you are away

(12 V DC) ON/OFF.

from the vehicle for several hours.

12. Black (ground)

To vehicle (metal) body.

13. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to connect

to both connectors.

14. Speaker leads

White: Front left +

ACC position

No ACC position

White/black: Front left ≠

•

The black lead is ground. Please ground this lead

Gray: Front right +

separately from the ground of high-current prod-

Gray/black: Front right ≠

ucts such as power amps.

Green: Rear left +

If you ground the products together and the

Green/black: Rear left ≠

ground becomes detached, there is a risk of dam-

Violet: Rear right +

age to the products or fire.

Violet/black: Rear right ≠

15. Connecting cords with RCA pin plugs (sold sep-

•

Cords for this product and those for other prod-

arately).

ucts may be different colors even if they have the

16. Power amp (sold separately)

same function. When connecting this product to

another product, refer to the supplied Installation

manuals of both products and connect cords that

have the same function.

17. Yellow/black

If you use a cellular telephone, connect it via the

Audio Mute lead on the cellular telephone. If not,

keep the Audio Mute lead free of any connec-

tions.

18. Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

19. System remote control

20. Rear speaker (Left)

21. Rear speaker (Right)

22. Perform these connections when using a different

amp (sold separately).

23. Blue/white (6*)

24. Blue/white (7*)

To Auto-antenna relay control terminal (max.

300 mA 12 V DC).

25. The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control type. In another

type of vehicle, never connect 6* and 7*.