Pioneer DEH-8400BT Bedieningshandleiding - Pagina 17
Blader online of download pdf Bedieningshandleiding voor {categorie_naam} Pioneer DEH-8400BT. Pioneer DEH-8400BT 37 pagina's. Cd rds receiver
Ook voor Pioneer DEH-8400BT: Snelstarthandleiding (8 pagina's), Installatiehandleiding (37 pagina's)
Pagina afdrukken
Section
02
Operating this unit
3
Turn M.C. to select the audio function.
After selecting, perform the following proce-
dures to set the audio function.
Fader/Balance (fader/balance adjustment)
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between fader (front/rear) and
balance (left/right).
3 Turn M.C. to adjust the front/rear speaker bal-
ance.
! The front/rear speaker balance cannot be ad-
justed when the rear output setting is Rear
SP :S/W. Refer to S/W control (rear output
and subwoofer setting) on page 21.
4 Turn M.C. to adjust the left/right speaker balance.
Preset EQ (equalizer recall)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select an equalizer curve.
Powerful—Natural—Vocal—Custom1—Cus-
tom2—Flat—Super bass
G.EQ (equalizer adjustment)
You can adjust the currently selected equalizer curve
setting as desired. Adjusted equalizer curve settings
are stored in Custom1 or Custom2.
! A separate Custom1 curve can be created for
each source. If you make adjustments when a
curve other than Custom2 is selected, the equali-
zer curve settings will be stored in Custom1.
! A Custom2 curve that is common for all sources
can be created. If you make adjustments when
the Custom2 curve is selected, the Custom2
curve will be updated.
1 Recall the equalizer curve you want to adjust.
2 Press M.C. to display the setting mode.
3 Press M.C. to cycle between equalizer band and
level.
4 Turn M.C. to select the equalizer band to adjust.
100Hz—315Hz—1.25kHz—3.15kHz—8kHz
Turn M.C. to adjust the equalizer curve.
+6 to –6 is displayed as the equalizer curve is in-
creased or decreased.
Loudness (loudness)
Loudness compensates for deficiencies in the low-fre-
quency and high-frequency ranges at low volume.
1 Press M.C. to display the setting mode.
2 Press M.C. to turn loudness on or off.
3 Turn M.C. to select the desired setting.
Low (low)—Mid (mid)—High (high)
Subwoofer1 (subwoofer on/off setting)
16
En
This unit is equipped with a subwoofer output which
can be turned on or off.
1 Press M.C. to display the setting mode.
2 Press M.C. to turn subwoofer output on or off.
3 Turn M.C. to select the phase for the subwoofer
output.
Turn M.C. to the left to select reverse phase, and
Reverse appears in the display. Turn M.C. to the
right to select normal phase, and Normal appears
in the display.
Subwoofer2 (subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the cut-off frequency
and the output level for the subwoofer.
3 Turn M.C. to select the cut-off frequency.
50Hz—63Hz—80Hz—100Hz—125Hz
4 Turn M.C. to adjust the output level for the sub-
woofer.
The subwoofer level increases or decreases each
time you turn M.C. +6 to –24 is displayed as the
level is increased or decreased.
Bass Booster (bass boost)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select a desired level.
0 to +6 is displayed as the level is increased or de-
creased.
HPF (high pass filter adjustment)
When you do not want low sounds from the subwoo-
fer output frequency range to play from the front or
rear speakers, turn on the HPF (high pass filter). Only
frequencies higher than those in the selected range
are output from the front or rear speakers.
1 Press M.C. to display the setting mode.
2 Press M.C. to turn high pass filter on or off.
3 Turn M.C. to select the cut-off frequency.
50Hz—63Hz—80Hz—100Hz—125Hz
Autogood products «130»