Pioneer DEH-P5100UB - Radio / CD Installatiehandleiding
Blader online of download pdf Installatiehandleiding voor {categorie_naam} Pioneer DEH-P5100UB - Radio / CD. Pioneer DEH-P5100UB - Radio / CD 8 pagina's. Cd rds receiver
Ook voor Pioneer DEH-P5100UB - Radio / CD: Installatiehandleiding (6 pagina's), Brochure (9 pagina's), Snelstarthandleiding (8 pagina's)
Pagina afdrukken
CD RDS RECEIVER
REPRODUCTOR DE CD CON RECEPTOR RDS
CD RDS-EMPFÄNGER
AUTORADIO CD RDS
SINTOLETTORE CD RDS
CD RDS-ONTVANGER
CD RDS ПРИЕМНИК
DEH-P5100UB
Installation Manual
Manual de instalación
Installationsanleitung
Manuel d'installation
Manuale d'installazione
Installatiehandleiding
Руководство по установке
Printed in Thailand
Imprimé en Thaïlande
QRD3025-A/N
<
> EW
<KOKZX> <08K00000>
Installation
English
3. Install the unit as illustrated.
Note
Mounting sleeve
• Check all connections and systems before final
Dashboard
installation.
• Do not use unauthorized parts. The use of
182
unauthorized parts may cause malfunctions.
Rubber bush
• Consult with your dealer if installation requires
53
drilling of holes or other modifications of the
vehicle.
• Do not install this unit where:
Screw
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
of a sudden stop.
Removing the Unit
• The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
1. Extend top and bottom of the trim
such as near the heater outlet.
ring outwards to remove the trim
• Optimum performance is obtained when the unit is
ring. When reattaching the trim ring,
installed at an angle of less than 60°.
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not fit
60°
properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
DIN Front/Rear-mount
Trim ring
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
2. Insert the supplied extraction keys
DIN Front-mount
into both sides of the unit until they
click into place.
Installation with the rubber bush
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by using
a screwdriver to bend the metal tabs
(90°) into place.
3. Pull the unit out of the dashboard.
Installation
English
DIN Rear-mount
Fastening the front panel
If you do not plan to detach the front panel,
1. Extend top and bottom of the trim
the front panel can be fastened with supplied
ring outwards to remove the trim
screw.
ring. When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not fit
properly.)
• It becomes easy to remove the trim ring if the
Screw
front panel is released.
Trim ring
2. Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
3. Tighten two screws on each side.
• Use either truss screws (5 mm × 8 mm)
or flush surface screws (5 mm × 9 mm),
depending on the shape of screw holes in the
bracket.
Screw
Dashboard or Console
Factory radio mounting bracket