Pioneer DEH-P8400BH Gebruikershandleiding - Pagina 12
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Pioneer DEH-P8400BH. Pioneer DEH-P8400BH 39 pagina's. Cd rds receiver
Pagina afdrukken
Section
Operating this unit
02
Loudness (loudness)
Loudness compensates for deficiencies in the low-
frequency and high-frequency ranges at low vol-
ume.
1 Press M.C. to display the setting mode.
2 Press M.C. to turn loudness on or off.
3 Turn M.C. to select the desired setting.
Low (low)—Mid (mid)—High (high)
Subwoofer1 (subwoofer on/off setting)
This unit is equipped with a subwoofer output
which can be turned on or off.
1 Press M.C. to display the setting mode.
2 Press M.C. to turn subwoofer output on or off.
3 Turn M.C. to select the phase for the sub-
woofer output.
Turn M.C. to the left to select reverse phase,
and Reverse appears in the display. Turn M.C.
to the right to select normal phase, and Nor-
mal appears in the display.
Subwoofer2 (subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the cut-off fre-
quency and the output level for the subwoofer.
3 Turn M.C. to select the cut-off frequency.
50Hz—63Hz—80Hz—100Hz—125Hz
4 Turn M.C. to adjust the output level for the sub-
woofer.
The subwoofer level increases or decreases
each time you turn M.C. +6 to –24 is displayed
as the level is increased or decreased.
Bass Booster (bass boost)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select a desired level.
0 to +6 is displayed as the level is increased or
decreased.
12
En
HPF (high pass filter adjustment)
When you do not want low sounds from the sub-
woofer output frequency range to play from the
front or rear speakers, turn on the HPF (high pass
filter). Only frequencies higher than those in the
selected range are output from the front or rear
speakers.
1 Press M.C. to display the setting mode.
2 Press M.C. to turn high pass filter on or off.
3 Turn M.C. to select the cut-off frequency.
50Hz—63Hz—80Hz—100Hz—125Hz
SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
! When selecting FM as the source, you cannot
switch to SLA.
! Settings are based on the FM volume level,
which remains unchanged.
! The AM volume level can also be adjusted with
this function.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to –4
Using Bluetooth wireless
technology
! Only for DEH-P8400BH
Using Bluetooth telephone
Important
! Since this unit is on standby to connect with
your cellular phone via Bluetooth wireless
technology, using it without the engine run-
ning can drain the battery power.
! Operations may vary depending on the kind
of cellular phone.
Operating this unit
! Advanced operations that require attention
such as dialing numbers on the monitor,
using the phone book, etc., are prohibited
while driving. Park your vehicle in a safe
place when using these advanced opera-
tions.
Setting up for hands-free phoning
Before you can use the hands-free phoning
function you must set up the unit for use with
your cellular phone.
1 Connection
Operate the Bluetooth telephone connection
menu. Refer to Connection menu operation on
this page.
2 Function settings
Operate the Bluetooth telephone function
menu. Refer to Phone menu operation on page
14.
Basic operations
Making a phone call
! Refer to Phone menu operation on page 14.
Answering an incoming call
1 When a call is received, press M.C.
Ending a call
1 Press PHONE.
Rejecting an incoming call
1 When a call is received, press PHONE.
Answering a call waiting
1 When a call is received, press M.C.
Switching between callers on hold
1 Press M.C.
Canceling call waiting
1 Press PHONE.
Adjusting the other party's listening volume
1 Turn LEVER while talking on the phone.
! When private mode is on, this function is not
available.
Turning private mode on or off
1 Press BAND/
while talking on the phone.
Switching the information display
1 Press
/DISP while talking on the phone.
Notes
! If private mode is selected on the cellular
phone, hands-free phoning may not be avail-
able.
! The estimated call time appears in the dis-
play (this may differ slightly from the actual
call time).
Connection menu operation
Important
! Be sure to park your vehicle in a safe place
and apply the parking brake when perform-
ing this operation.
! Connected devices may not operate properly
if more than one Bluetooth device is con-
nected at a time (e.g. a phone and a separate
audio player are connected simultaneously).
1
Press and hold PHONE to display the con-
nection menu.
# You cannot operate this step during a call.
2
Turn M.C. to select the function.
After selecting, perform the following proce-
dures to set the function.