Pioneer PRS-D1000M Gebruikershandleiding - Pagina 4
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Pioneer PRS-D1000M. Pioneer PRS-D1000M 9 pagina's. Class d mono amplifier
Ook voor Pioneer PRS-D1000M: Gebruikershandleiding (50 pagina's), Gebruikershandleiding (9 pagina's), Servicehandleiding (38 pagina's)
Pagina afdrukken
Installation
CAUTION
CAUTION:
• Do not install in:
To prevent malfunction and/or injury
—Places where it could injure the driver or pas-
• To ensure proper heat dissipation of the amplifier,
sengers if the vehicle stops suddenly.
be sure of the following during installation.
—Places where it may interfere with the driver,
—Allow adequate space above the amplifier for
such as on the floor in front of the driver's
proper ventilation.
seat.
—Do not cover the amplifier with a floor mat or
• Make sure that wires are not caught in the sliding
carpet.
mechanism of the seats, resulting in a short-cir-
• DO NOT allow amplifier to come into contact
cuit.
with liquids due to, for example, the location
• Confirm that no parts are behind the panel when
where the amplifier is installed. Electrical shock
drilling a hole for installation of the amplifier.
could result. Also, amplifier and speaker damage,
Protect all cables and important equipment such
smoke, and overheating could result from contact
as fuel lines, brake lines and electrical wiring
with liquids. In addition, the amplifier surface and
from damage.
the surface of any attached speakers could become
• Install tapping screws in such a way that the screw
hot to the touch and minor burns could result.
tip does not touch any wire. This is important to
• Do not install the amplifier on unstable places
prevent wires from being cut by vibration of the
such as the spare tire board.
car, which can result in fire.
• The best location for installation differs with the
• DO NOT allow amplifier to come into contact
car model and installation location. Secure the
with liquids due to, for example, the location
amplifier at a sufficiently rigid location.
where the amplifier is installed. Electrical shock
• Make temporary connections first and check that
could result. Also, amplifier and speaker damage,
the amplifier and the system operate properly.
smoke, and overheating could result from contact
• After installing the amplifier, confirm that the
with liquids. In addition, the amplifier surface and
spare tire, jack and tools can be easily removed.
the surface of any attached speakers could become
hot to the touch and minor burns could result.
• To ensure proper installation, use the supplied
parts in the manner specified. If any parts other
than the supplied ones are used, they may damage
internal parts of the amplifier, or they may
become loose causing the amplifier to shut down.
• Never replace the fuse with one of greater value
or rating than the original fuse. Use of an improp-
er fuse could result in overheating and smoke and
could cause damage to the product and injury
including burns.
<ENGLISH>
Example of installation on the floor
mat or on the chassis
1. Place the amplifier where it is to be
installed. Insert the supplied tapping
screws (4 × 18 mm) into the screw
holes. Push on the screws with a
screwdriver so they make marks
where the installation holes are to be
located.
2. Drill 2.5 mm diameter holes at the
point marked, and install the ampli-
fier, either on the carpet or directly
to the chassis.
Replacing the terminal cover
1. Align the unit and terminal cover,
and insert the screw.
2. Tighten the screw with a 4 mm
hexagonal wrench.
Tapping-screws
Screw
(4 × 18 mm)
Terminal Cover
Floor mat
or chassis
Drill a 2.5 mm diameter hole
Specifications
<ENGLISH>
Power source ........................................................................................................ 14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system .......................................................................................................................................... Negative type
Current consumption ...................................................................................................... 39 A (at continuous power, 4 Ω)
Average current drawn* .......................................................................................................... 12 A (4 Ω for one channel)
20 A (2 Ω for one channel)
28 A (1 Ω for one channel)
Fuse (external) ...................................................................................................................................................... 40 A × 2
Dimensions .................................................................................................................... 304 (W) × 56 (H) × 202 (D) mm
Weight .................................................................................................................... 3.0 kg (Leads for wiring not included)
Maximum power output .............................................................................. 800 W × 1 (4 Ω) / 1 200 W × 1 (1 Ω to 2 Ω)
Continuous power (14.4 V) .................................... NORMAL mode: 4 Ω, 20 Hz to 240 Hz,
1.0% THD, 400 W × 1
2 Ω, 100 Hz,
1.0% THD, 600 W × 1
HI-CURRENT mode: 4 Ω, 20 Hz to 240 Hz,
1.0% THD, 150 W × 1
2 Ω, 100 Hz,
1.0% THD, 300 W × 1
1 Ω, 100 Hz,
1.0% THD, 600 W × 1
Load impedance ...................................................................................................................... 4 Ω (1 Ω to 8 Ω allowable)
Frequency response ........................................................................................................ 10 Hz to 240 Hz (+0 dB, –3 dB)
S/N ratio ........................................................................................................................................ 92 dB (IEC-A network)
Distortion .......................................................................................................................................... 0.5 % (10 W, 100 Hz)
Low pass filter ............................................................................................................ Cut off frequency: 40 Hz to 240 Hz
Cut off slope: –18 dB/oct
Subsonic filter (HPF) .............................................................................................................................. Frequency: 20 Hz
Slope: –18 dB
Bass boost ................................................................................................................................................ Frequency: 50 Hz
Level: 0 / 6 / 9 / 12 dB
Gain control .................................................................................................................................... RCA: 400 mV to 6.5 V
SP: 1,6 V to 26 V
Maximum input level / impedance .................................................................................................... RCA: 6.5 V / 22 kΩ
SP: 26 V / 90 kΩ
Note:
• Specifications and the design are subject to possible modification without notice
due to improvements.
*Average current drawn
• The average current drawn is nearly the maximum current drawn by this unit
when an audio signal is input. Use this value when working out total current
drawn by multiple power amplifiers.