Pioneer CMX-3000 Gebruiksaanwijzing - Pagina 18

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Pioneer CMX-3000. Pioneer CMX-3000 20 pagina's. Owner's manual
Ook voor Pioneer CMX-3000: Gebruiksaanwijzing (33 pagina's)

Pagina afdrukken

1. Remote Control Unit

Applications (Advanced operations)

Remote control unit

PITCH BEND+,–

TRACK

(4,¢)

CUE

PLAY/

PAUSE

(3 8)

Jog dial

Press the BPM SYNC button.

¶ The BPM SYNC button will flash and the player enters the

BPM synchro playback mode.

¶ If both players are currently in playback mode, no

synchronization is possible until playback is stopped on one

of the players. When one player is stopped, the player still

playing back is considered the master.

¶ If start is begun when the BPM on the slave player is

unknown, synchro playback will begin at the point the slave's

BPM value is measured.

¶ During BPM synchro, the MASTER indicator will light on the

"master" player's display. On the slave player, the tempo

control range display will turn off and the tempo change rate

display will show the tempo compensation value.

¶ During BPM synchro, the slave player's tempo will change to

match any tempo changes on the master side. In this case,

the tempo and pitch bend of the slave player cannot be

independently adjusted.

¶ If playback is interrupted on the master player, the slave

player will become the master.

When this occurs, if the tempo control of the new master

player is at a different setting from the tempo of the currently

playing track, the display will alternately show the message

dEc (or Inc), and the amount of tempo deviation. To reduce

the tempo deviation to zero, move the tempo control slide to

the "–" side if dEc is displayed, and to the "+" side if Inc is

displayed. Speed control using the tempo control slide

becomes possible when the tempo has been adjusted.

7 Correcting beat timing

¶ When beat is detected during BPM synchro, the ring display

will light to graphically indicate the four-beat timing.

¶ The four-beat timing of the currently playing track on players

A, B can be designated by tapping the TAP button with that

timing once on each of the two players. The beat timing of

the slave player will be automatically brought into

correspondence with that of the master player, so as to

match the designated beat timing.

NOTES:

¶ It may not be possible to correctly measure the BPM value

for some tracks. If this happens, press the TAP button in time

with the beat to enable a more accurate BPM synchro

playback. However, if the BPM synchro range is outside the

adjustable range of the player, appropriate BPM synchro

playback may not be possible.

¶ During BPM synchro, the tempo control slide and pitch bend

operations are disabled on the slave player.

Fader Start Playback (*)

The provided control cable may be used to connect the control

jack on the CMX-3000 to a control jack on a DJM-300, DJM-500,

or DJM-600 mixer, thus making it possible to exit from cueing

standby mode and to start playback immediately by raising the

DJ mixer CHANNEL FADER. The CROSS FADER may also be

used to perform fading starts on the player as well. The fader

may also be returned to its original position to return the player

to the cueing point (i.e., to perform back cueing). (This does not

apply, however, during auto playback.) (See p. 10 for

instructions on how to connect the player and mixer.)

RELAY PLAY

MASTER

TEMPO

BPM SYNC

Tempo control slide

Relay Play Using Two Players (*)

÷ Set both player's auto cue function to ON (the A. CUE

indicators will light in the displays).

÷ Set your DJ mixer's fader control to its center position.

1. Press the RELAY PLAY button to blink the button

indicator.

2. Begin playback on the first player.

3. When the currently playing track ends, playback

will begin automatically on the standby player.

4. The first player will enter cue standby mode at the

beginning of the next track on its disc.

¶ By repeating this operation, the two players can be used

to perform continuous relay play.

¶ By loading new discs on the standby player, you can

construct a continuous program of whatever tracks you

wish.

¶ By setting a Cue point on the standby player, you can

perform relay to any desired Cue point on the selected

track (see page 13: Cueing Point Settings).

NOTES:

÷ Fader start and relay play cannot be performed simultane-

ously.

÷ When the Auto Cue function is off, replay will be performed

of the entire disc.

Data Copy

WAVE and other data recorded in this unit can be copied to

another CMX-3000 if desired.

1. With the unit power off, use a control cord to

connect the two player's DATA IN/OUT connec-

tors.

2. On each CMX-3000, turn on power while simulta-

neously pressing the EJECT buttons on players A

and B. (The remote control unit's EJECT button

cannot be used for this operation.)

÷ The power will turn on, and data copy mode (slave mode)

will be established; the display will show "SLAVE M".

3. With both units in the data copy mode ("slave

mode"), press the CD TEXT/WAVE button on the

player A holding the WAVE data you wish to copy.

Hold the button depressed for one second.

÷ This unit will enter the master mode and the display will

show "MASTER."

4. Press the PLAY/PAUSE button (38) of Player A on

the "master" unit.

÷ Data copying will begin, and the 38 indictor will flash.

÷ About ten minutes will be required for the copy operation.

END is displayed on the master when copying is

completed.

5. Turn off the power on both units and disconnect

the control cord.

÷ When power is turned on again, operation will return to

normal mode.

NOTES:

÷ Do not turn off the power or disconnect cables during

copying to prevent corruption of the copying data.

÷ If the ERROR message is displayed during data copy, check

your connections and perform the data copy function again.