Ariston AW 149 NA Gebruiks- en installatiehandleiding - Pagina 6
Blader online of download pdf Gebruiks- en installatiehandleiding voor {categorie_naam} Ariston AW 149 NA. Ariston AW 149 NA 40 pagina's. Washer ariston
Ook voor Ariston AW 149 NA: Brochure & specificaties (8 pagina's), Reparatiehandleiding (22 pagina's)
Pagina afdrukken
Start and Programs
The Controls
PROGRAMS knob
EN
! Warning, if after pressing the start button, the
programs knob position has changed, the new
position will NOT change the program selected.
! Position 0, turning the knob to position 0 resets and
cancels a program, the display shows
OPTION buttons / lights
These buttons are used to customize the selected
program to your requirements. A program must have
been selected on the programs knob before an option
can be selected. Not all options are available for all
programs (see Start and Programs). If an option is not
available and you press the button, the buzzer will
beep three times. If the option is available there will
be one beep and the option light next to the button
lights to confirm the selection.
After the start button has been pressed only the
Alarm, Pre Creasecare and Post Creasecare options
can be changed.
Time Delay
The start of some programs (see Start and Programs)
can be delayed for up to 18 hours.
Press this button, the display shows
option light comes on. Press again and a 1 hour delay is
selected and the display indicates 1hr, each further press
of the button adds 1hr to the delay. When 18hr is displayed
a further press and the display shows
couple of seconds cancels the delay. You can also cancel
the delay by turning the programs knob to 0, wait for the
buzzer to beep and then turn back to your selected program.
Pre Creasecare
This option is only available if a delayed start has been
selected. It tumbles the clothes occasionally during the
delayed period to help prevent creases developing.
High Heat
When available this button selects high heat. Press this
button and a high heat setting is selected and the light
alongside the button comes on.
Timed programs have a default of low heat, if the light
alongside the button is on then pressing the button selects
a low heat setting and the light goes out. The heat icon
on the display will also change.
Alarm
Available on all programs and allows the buzzer to give a
signal at the end of the drying cycle, to remind you that
the clothes are ready to be removed.
Press the button and the light will show that the option is
selected.
Post Creasecare
When available and selected, the clothes are occasionally
tumbled after the end of the drying and air fluff cycles,
to help prevent creases developing should you not be
available to remove the load immediately the
program is complete.
6
O8
.
OFF
and the
OFF
and after a
DISPLAY
The display shows either the amount of time delay
remaining or an indication of the amount of time left for
a drying program.
The delay time is displayed in hours and counts down
each hour.
The time to end is displayed in hours and minutes and
counts down each minute, this time includes the air
fluff phase. When timed programs are selected the
time displayed throughout the cycle is the actual time
remaining.
When a sensing program is selected the time
displayed is an estimate of the time remaining. When
the program is selected the display shows the time
required to dry a full load, after around 10 minutes the
controller calculates a better estimate of the cycle
time.
The colons between the hours and minutes in the
display flash to show that the time is counting down.
When the program finishes its air fluff phase the
E88
display will show
.
The display also shows if there is a problem with your
dryer, if this occurs the display will show F followed by
a fault code number (see Troubleshooting).
Door Opening
Opening the door during a program will stop the dryer
and have the following effects:
All 4 progress lights come on.
During a delay phase the delay will continue
to count down. The start button must be
pressed to resume the delay program.
The progress lights will change to show
current status.
During the drying part of the program, the
time to end count continues but the colons
do not flash. The start button must be
pressed to resume the program. The progress
lights will change to show the current status.
During the air fluff or post creasecare phase
of a drying program and anytime during an
Airing or Air fluff program, the program will
finish. Pressing the start button will re-start a
new program at the beginning.
Changing the programs knob will select a new
program, after you press the start button. You
can use this to select the Air Fluff program to
cool the clothes, if you find them dry enough.
Note
If you have a power outage, switch off the power or
remove the plug, press the START button and the
program will resume.