Pioneer ]S-2EX Servicehandleiding - Pagina 8

Blader online of download pdf Servicehandleiding voor {categorie_naam} Pioneer ]S-2EX. Pioneer ]S-2EX 10 pagina's. Pioneer speaker system operating instructions
Ook voor Pioneer ]S-2EX: Catalogus (20 pagina's), Brochure & specificaties (16 pagina's), Gebruiksaanwijzing (26 pagina's)

Pioneer ]S-2EX Servicehandleiding
1
2.3.3 Removal/Reattachment of Acoustic absorbent pads
Removal/reattachment of acoustic absorbent pads is necessary before or after removal/reattachment of the Network Assy.
A
Note:
When reattaching the Network Assy for the midrange/tweeter, before reattaching the closure panel, be sure to remove the
acoustic absorbent pads located behind the chamber. (See Fig. 2-11.) If the closure panel pinches an acoustic absorbent
pad when it is secured, air leakage may occur, which may result in poor performance of this speaker system.
1. Acoustic absorbent pads around the input terminals
B
Fig. 2-5: After the woofer is removed (1)
C
Fig. 2-6: After the woofer is removed (2)
D
Fig. 2-7: After the woofer is removed (3)
E
Fig. 2-8: After the woofer is removed (4)
F
8
1
2
1 Remove this acoustic absorbent pad.
When reattaching, roll it and push it
in deep behind the cabinet.
As only this acoustic absorbent pad
must be fixed with adhesive, before
pushing it in, apply adhesive to the
upper area of the input terminals.
(Adhesive: DIABOND black/GYL-014)
2 Remove this acoustic absorbent pad.
When reattaching, cover it over the
concave portion of the input terminals
fitting portion.
3 Remove this acoustic absorbent pad.
When reattaching, fold it in half
lengthwise and push it into the upper
and lower parts of the input terminal.
1 Remove this acoustic absorbent pad.
When reattaching, place it so that it
covers the Network Assy and that
the Network Assy cannot be seen
when you look inside from the duct.
In this state, remove or reattach the
Network Assy.
S-2EX
2
3
2. Acoustic absorbent pads inside the chamber for
the midrange/tweeter
2 Remove this acoustic absorbent pad.
1 Remove these acoustic absorbent
3 Remove this acoustic absorbent pad
Fig. 2-9: After the midrange/tweeter is removed (1)
Fig. 2-10: After the midrange/tweeter is removed (2)
3. Acoustic absorbent pads around the Network Assy
for the midrange/tweeter
When reattaching, lay one acoustic absorbent pad on another
and fold them lengthwise into four.
Push it in, in the direction shown in the illustration below,
along the upper board of the cabinet and the rear panel of the
chamber.
Front
Fig. 2-11: After the woofer is removed (5)
3
4
When reattaching, lay it along the
upper board inside the chamber.
pads. When reattaching, roll them
and push them in so that they come
near the baffle board and side board.
When reattaching, place it along the
surface inside the chamber so that it
forms a U shape.
4 Remove this acoustic absorbent
pad from the closure panel section.
When reattaching, fold it in half
lengthwise and push it in.
Remove the acoustic absorbent
pad from the back board and
remove the screws of the closure
panel.
5 Remove the acoustic absorbent
pads stuffed in the space behind
the chamber for the midrange/
tweeter.
Insert your hand in the direction of
the arrow to remove.
Removal/reattachment of the
Network Assy for the midrange/
tweeter and of the closure panel
must be done in this state.
Up
4