Ariston LGO30L Handmatig - Pagina 21

Blader online of download pdf Handmatig voor {categorie_naam} Ariston LGO30L. Ariston LGO30L 21 pagina's.

Pagina afdrukken
INSTALLATION AND WARRANTY INSTRUCTIONS
IT IS THE RESPONSIBILITY OF THE INSTALLER TO INFORM THE END USER OF THE INSTALLATION, MAINTENANCE & REPAIR REQUIREMENTS FOR
THIS WATER HEATER IN ACCORDANCE WITH SANS 10254 AND THE MANUFACTURERS REQUIREMENTS.
INSTALLATION INSTRUCTIONS - PLUMBING
TO BE INSTALLED BY A QUALIFIED PLUMBER AND TO COMPLY WITH
SANS 10254 & 10252-1
INSTALLER TO ISSUE A PLUMBING CERTIFICATE OF COMPLIANCE
This water heater must be fitted with the supplied TP VALVE before installation.
Always fit this water heater with a PRESSURE CONTROL VALVE and EXPANSION
CONTROL VALVE (which may be combined in one unit) not exceeding the kPa rating
of the water heater as stated on the serial label. TP VALVE and EXPANSION VALVE
overflow pipes must be led separately to the outside of the building in a continuous
downward direction, in a frost free ambient with the outlets being left open to the
atmosphere, and in case of the TP VALVE must be copper. The EXPANSION VALVE is
designed to drip under normal operating conditions and must never be plugged.
1. Flush the cold water supply line prior to connecting.
2. Check that the control valve is free from dirt.
3. Ensure all piping and water heater brackets are securely fixed.
4. After connecting the installation, open one or more hot water taps and
open the cold water to dispel air from the system.
5. Close all hot taps to bring water heater under pressure.
6. Check all plumbing connections for leaks.
7. Installation diagrams must be complied with in all respects.
8. The installation of a drip tray is required where water leaking from the
water heater or connections could cause consequential damage.
INSTALLATION INSTRUCTIONS - ELECTRICAL
ELECTRICAL WORK TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
AND TO COMPLY WITH SANS 10142-1
WARNING: THIS APPLIANCE MUST BE EARTHED & BONDED
2
1. Heat resisting round 2.5mm (minimum) 3 core stranded cable should be used to
connect the electrical supply.
2. A double pole isolator switch to be installed within 1m of the water heater -
correctly rated for the element size.
3. Circuit breaker on distribution board to be correctly rated for the element size.
4. Turn off the circuit breaker on the distribution board as well as the isolator at the
water heater.
5. Remove the electrical access panel.
6. Cut away tips of old electrical wire, stripping away the insulation.
7. Connect and tightly secure electrical connection to the thermostat / terminal block.
Ensuring thermostat is tightly inserted into the element.
8. Replace electrical access panel.
9. Ensure the water heater is full of water before switching on electricity, even for testing
purposes.
10. Heating element will burn out if turned on without water.
INSTALLATION INSTRUCTIONS - WALL MOUNTING
1. Remove brackets from the floor mounting position and bolt to side of the unit in the
wall mounting position.
2. Bolt unit to the wall using suitable rated fixation bolts.
NOTE: 200L & 250L UNIT MAY NOT BE WALL MOUNTED
MAINTENANCE INSTRUCTIONS
SWITCH OFF ELECTRICAL SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE OR
REPAIRS ON THE WATER HEATER
REPLACEMENT OF THERMOSTAT
1. Disconnect wiring, remove thermostat by pulling it out of it's pocket.
2. Fit new thermostat, ensuring the stem of the thermostat is not bent or damaged in any
way. On electronic models, ensure that the metallic thermostat bulb is inserted before
the wired probe.
3. Reconnect wiring to thermostat ensuring connections are clean, tight and secure.
4. Set thermostat to 60˚C or as required by user.
REPLACEMENT OF ELEMENT
1. Drain water from the water heater.
2. Remove thermostat as above and remove flange lid from cylinder.
3. Remove old element and gasket from flange lid.
4. Fit new element and gasket to flange lid.
5. Refit flange lid, and replace thermostat as above.
REPLACEMENT OF ANODE
1. The magnesium anode installed in a vitreous enamel lined steel water heater will
slowly dissipate whilst protecting the cylinder.
2. The life of the cylinder may be extended by replacing the anode.
3. Inspect the anode yearly, and if required, replace the anode.
4. Replacement of the anode should be carried out at minimum 2 year intervals, during the
warranty period, to ensure protection of the steel cylinder.
5. The life expectancy of the anode would be dependent on the water quality in the area,
which the water authority can advise on.
6. A guideline below ( as reference only):
TOTAL DISSOLVED SOLIDS
RECOMMENDED
PPM
REPLACEMENT
0 - 400
3
Years
400 - 600
2
Years
Over 600
1
Year
Fitment of an aluminium anode is recommended for harsh water conditions.
7. When water is supplied from a borehole or well, anodes should be replaced at least
once a year.
8. Replace anode as follows:
(a) Drain water heater.
(b) Remove anode cover and unscrew anode from cylinder.
(c) Fit new anode and replace anode cover.
THE ANODE IS A MAINTAINABLE COMPONENT
Manufactured by: HEAT TECH GEYSERS (PTY) LTD
294 Barolong Street, Sunderland Ridge
Tel: 087 943 7471
After-Sales Service: 087 943 7470 / [email protected]
ALL PIPE WORK AND COMPONENTS CONNECTED TO THE INLET, OUTLET AND T&P VALVE SHOULD BE THERMALLY INSULATED FOR 2 METERS.
THE THERMAL INSULATION SHALL COMPLY WITH THE REQUIREMENTS OF SANS 10252-1, SANS 10254, SANS 10400-XA AND SANS 204.
Anti-Siphon Loop
Above Top of Water Heater
Vacuum Breaker
Motor Valve *1
Stopcock
Mains Pressure
Pressure Control Valve *2
Balanced Cold Water
Brass Extension *3
THIS WATER HEATER IS FITTED WITH A MAGNESIUM ANODE THAT REQUIRES PERIODIC REPLACEMENT
Outlet
Electrical
Inlet
Cover
200L & 250L NOT TO BE
WALL MOUNTED
Stopcock
Mains Pressure
Pressure Control Valve *2
Balanced Cold Water
50L & 250L SHOULD NOT BE INSTALLED VERTICALLY.
*1 Optional extra for certain models only
*2 Refer to the serial label for the correct pressure rating of the water heater.
*3 Supplied on certain models only.
*4 Solar or heat pump compatible when used in conjunction with a dual drain cock.
*5 When not using the additional socket for solar or heat pump - ENSURE THAT THE SOCKET IS PLUGGED.
The following minimum installation clearance must be allowed for on the electrical side of the water heater in the event of
having to remove the element, thermostat or the anodes and 500mm on the opposite side.
50L - 500mm
100L - 700mm
WARRANTY
*T & C Apply
This water heater is warrantied against faulty materials and/or workmanship not withstanding anything to the contrary
contained herein. The company will repair or at it's own discretion, replace a defective unit or parts inclusive of labour costs during
the warranty period. The repaired or replaced part, or water heater, warranty will still be calculated from original date of
manufacture, not from the repaired or replacement date.
The period of warranty is calculated from the date of manufacturing as indicated on the serial plate. This is the only warranty given
and it expressly excludes all other warranties, expressed or implied by law. The warranty expressly covers the water heater only
and does NOT cover any other part or parts of the installation which may, because of the failure or defect of the water heater
become damaged in any way whatsoever and under no circumstances shall the manufacturer be liable for any direct, indirect or
consequential loss suffered by the consumer and/or third party.
The warranty is subjected to the following:
(a) The water heater is installed in accordance with SANS 10142-1: (Electrical) and SANS 10254 & 10252-1 (Plumbing) and in
accordance with any other applicable national and local regulations.
(b) The water heater is installed according to the manufacturers installation requirements.
(c) The water heater is maintained and serviced yearly.
(d) The anode is inspected yearly and replaced at least every second year for municipal water supplies.
(e) The serial plate is not damaged or tampered with in any way.
(f) The water heater is subjected to normal use with municipal water supply and proper installation by qualified personnel.
(g) This warranty will exclude any failure due to hard water conditions.
(h) Elements burnt out due to no water, or element and thermostat terminals burnt / melted are excluded
from this warranty.
(i) The above warranty is subject to only genuine replacement parts being used whilst the inner cylinder is still under warranty.
(j) The above warranty shall however be completely invalidated if any repairs are effected by the customer or others on his behalf in
an attempt, to remedy the alleged fault.
(k) Under no circumstances must the unit be removed from the installation.
(l) Sufficient access to the water heater for either repairs or replacement is the responsibility of the end user. The manufacturer will
not make good or reassemble any ceilings or cupboards.
(m) As per SANS 10254, no one-way valve or stop cock allowed between the water heater and expansion relief valve.
Web:www.heattech.co.za
Vacuum Breaker
Drain Cock *4
Supplied
Electrical Cover
HORIZONTAL INSTALLATION
Vacuum Breaker
Safety Valve
Anti-Siphon Loop
Above Top of Water Heater
Optional Anode
Heat Pump/Solar
Connection or Plug *5
Motor Valve *1
VERTICAL INSTALLATION
150L - 950mm
200L - 1500mm
WARRANTY PERIODS
Cylinder
Electrical Components
Gaskets
Drain Cock and T&P Valve
Anode
(consumable, service required)
Vacuum Breaker
200 mm
(MIN)
Safety Valve
Hot Water Outlet
Optional Anode
Heat Pump/Solar
Connection or Plug *5
Drip Tray
Vacuum Breaker
Hot Water
Outlet
Electrical Cover
Brass Extension *3
Supplied
Drain Cock *4
Drip Tray
250L - 1500mm
*T & C apply
5 Years
1 Year
1 Year
2 Years
None