Aeotec Z-Stick Gen5 Handmatig

Blader online of download pdf Handmatig voor {categorie_naam} Aeotec Z-Stick Gen5. Aeotec Z-Stick Gen5 2 pagina's. Z-wave usb adapter
Ook voor Aeotec Z-Stick Gen5: Gebruikershandleiding (5 pagina's), Handmatig (11 pagina's)

Pagina afdrukken

Aeotec by Aeon Labs Z-Stick.

Aeon Labs Z-Stick Gen5 is a self-

powered Z-Wave USB adapter with

remote network creation capabilities

(independent from external power and

host microprocessor). By being able

to remotely include/remove Z-Wave

devices, this greatly simplifies Z-Wave

network installation. When connected

to a host controller (via USB), it enables

the host controller to take part in the

Z-Wave Network.

The Z-Stick Gen5 is also device

firmware upgradeable by the end

consumer. This enables the product

to always have the latest Z-Wave

protocol, capabilities and commands.

By taking advantage of the Z-Wave

m e s h n e t w o r k , c o m m a n d s c a n

View the expanded manual:

be routed to their destination via

http://aeotec.com/support

intermediary "listening" Z-Wave

products. Products that are Z-Wave

certified can be used and communicate

with other Z-Wave certified devices.

Familiarize yourself with your

Z-Stick.

Action Button

Quick start.

The Z-Stick operates in three distinct

modes: Inclusion-Mode, Removal-

Mode and SerialAPI-Mode. Both

Inclusion-Mode and Removal-Mode

require the Z-Stick to be unplugged

from the USB connector of the host,

while SerialAPI-Mode requires that

the Z-Stick to be plugged into the

USB connector of the host. Software

drivers for the "ZW050x_USB_VCP_

PC_Driver" may need to be installed in

order for the Z-Stick to be recognized

on some computers (drivers can

be found at http://www.aeotec.com/

support).

Inclusion-Mode: Adding/Including

Z-Wave Devices into the Z-Wave

Network.

1. To initiate Inclusion-Mode, unplug the

Z-Stick from the USB connector and

then tap the Action Button. (The blue

LED will blink slowly.)

2. To include a new Z-Wave device into

the network, simply go to the device

with the Z-Stick and press the button

on the device you wish to include. (The

blue LED on the Z-Stick will blink fast

during a network neighbour discovery

and stay solid for 2 seconds to indicate

successful inclusion of the device into

the network.)

Reset Button

Installation and Maintenance

3. The blue LED will then return to

Application (IMA) feature.

blinking slowly, indicating readiness for

further device inclusions. Repeat step 2

for each device you wish to include.

When the Z-Stick is in Serial API-

Mode and acts a primary controller,

4. Tap the Z-Stick's Action Button to

it can measure the network health

turn it off or it will automatically exit

for each device in the network. The

the removal mode after 30 seconds of

different colour of LED indicates the

inactivity.

communication quality between the

Z-Stick Controller and devices in the

Removal-Mode: Deleting/

network.

Removing/Excluding Z-Wave

Install the IMA tool software first (note:

Devices from the Z-Wave Network.

the IMA tool can be downloaded from

here: http://www.aeotec.com/support).

1. To initiate Removal-Mode, unplug

Select the node device and then click

the Z-Stick from the USB connector.

the IMA test button to start the IMA test

Then press and hold down the Action

between the Central Controller and

Button for approximately 2 seconds.

the node devices. Your IMA tool client

(The orange LED will blink fast.)

will receive the test result and use

different colour of LED icon to indicate

2. To remove a Z-Wave device from the

the network health level, its colour will

network, simply go to the device with

be changed follow with the change of

the Z-Stick and press the button on the

network health level. If the colour of

device you wish to remove. (The blue

LED is changed to green

LED on the Z-Stick will immediately

stay solid for 2 seconds to indicate

means the current network quality is

successful removal from the network.)

good. If the colour of LED is changed to

orange

, which means the current

3. The orange LED will then return

network quality is acceptable but

to blink fast, indicating readiness for

latency can occur. If the colour of LED

further device exclusions. Repeat step

is changed to red

2 for each device you wish to exclude.

current network quality is insufficient.

4. Tap the Z-Stick's Action Button to

If the IMA tool return a , which means

turn it off or it will automatically exit

the removal mode after 30 seconds of

the current network is critical because

inactivity.

node is not responding.

When the Z-Stick acts an independent/

secondary controller that has been un-

plugged from the USB host, it also can

measure the network health in Z-Wave

network. The different colour of LED on

the Z-Stick indicates the communication

quality between the Central Controller

and the current location of Z-Stick in

the network.

Short press the Action Button 5 times, if

the colour of LED is changed to purple

and then it follows with fast blink, which

means it goes into the IMA feature.

The colour of LED will be changed

according to the network health

level. If the colour of LED is changed

to green, which means the current

communication quality is more than

95% on -7dBm. If the colour of LED

is changed to orange, which means

the current communication quality is

more than 95% on 0dBm. If the colour

of LED is changed to purple, which

means the current communication

, which

quality is less than 95% on 0dBm. If the

colour of LED is changed to red, which

means the current communication has

failed.

Short press the Action Button 5 times

again, the Z-Stick will automatically exit

, which means the

the IMA feature.

SerialAPI-Mode: Allowing a Host

Processor To Take Control of the

Z-Stick and Take Part in the Z-Wave

Network.

To initiate SerialAPI-Mode, plug the

Z-Stick into the USB connector of the

host (i.e. PC, MAC, or Gateway).

Note:

1). While in SerialAPI-mode, the

Z-Stick is always listening (it is awake

and always in RX receive mode) for

instructions and acts as a Z-Wave

adapter and responds to commands

sent through USB by the host processor

software.

2). Pressing the Action Button will not

have any effect while in SerialAPI-

Mode. But short pressing the Reset

Button will reset the USB port.

Add the Z-Stick to a pre-existing

Z-Wave network.

This must be done through the host

software which takes control of the

Z-Stick USB adapter while the Z-Stick

is in SerialAPI-Mode. Please consult

the instruction manual of the host

software to add the Z-Stick to a pre-

existing Z-Wave network (i.e. "Learn",

"Sync", "Add as Secondary Controller",

etc.). This function can only be

performed via host software.