Whirlpool 3354199 Handleiding voor installatie-instructies - Pagina 3

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Whirlpool 3354199. Whirlpool 3354199 8 pagina's.

Pagina afdrukken

TooIs needed for

instaIIation:

Parts supplied

for fnstalIation:

Remove parts from packages, Check

that all parts were included.

1 hose clamp

2 inlet hoses

4 flat water

hose washers

2 front leveling

legs with nuts

grounding

clamp

and screw

1 drain hose

Electrical

requirements

Electrical Shock Hazard

Electrical ground is required on

this product.

Improper connection

of the

equipment-groundtng

conductor

can result in electrical

shock.

Check with a quallfled

electrician

If you are In doubt as

to whether the appliance

properly

grounded.

Do Not modify the power supply

cord plug. If It will not fit the

outlet, have a proper outlet

installed by a quallfied

elec-

trician. Modifying

the power

supply cord plug could result in

electrical

shock.

Do Not use an extension

cord

with thts appltance.

Such use

could result in a fire, electrical

shock or other personal

injury.

Do Not have a fuse in the neutral

or grounding

circuit. This could

result In electrical

shock.

120-Volt, 60-Hz, AC-only, 15 or 20-

mpere fused electrical supply is

required. (Time-delay fuse or circuit

breaker is recommended.)

It is

recommended

that a separate

circuit serving only this appliance

be provided.

Recommended

grounding method

Do Not, under any circumstances

remove the power supply cord

grounding

prong.

For your personal safety, this appliance

must be grounded. This appliance

equipped

with a power supply cord

having a 3-prong grounding plug. To

minimize possible shock hazard, the

cord must be plugged

into a mating 3-

prong grounding-type

wall receptacle,

grounding in accordance

with National

Electrical Code, ANSI/NFPA 70 - latest

edition, and all local codes

J-prong

grounding

and ordinances. See Figurel. If a

type wall

receptacra

mating wall receptacle

is not available,

it is the

personal responsi-

bility and obligation

of the customer to

have a properly

grounded 3-prong

wall receptacle

installed

by a qualified electrician.

Figure 1

For added personal safety, use clamp

and green colored copper grounding

wire. Connect the grounding wire

(#IS minimum] from the external

grounding connector on the back

of the washer to a grounded cold

water pipe.' See Figure 2.

Do Not ground to a gas supply pipe

or hot water pipe.

Electrical ground is required on thls

appliance.

* Grounded

cold water

pipe

must have

metal

continuity

to electrical

ground

and not be

interrupted

by plastic,

rubber

or other electrical

insulating

connectors

such os hoses. finings.

washer

or gaskets

(including

water

meter or

pump).

Any electrical

insulating

connector

should

be jumped

os shown

in FiQUre 2 with No 4 wire

securely

clamped

to bare

metal

ot both ends.

Temporary

grounding method

Do Not, under any circumstances

remove the power supply cord

grounding

prong.

This method is not recommended.

If changing

and properly grounding the

wall receptacle

is impossible and

where local codes permit (consult your

electrical

inspector), a temporary

adaptor may be plugged

into the

existing 2-prong wall receptacle

mate with the J-prong power supply

cord. If this is done, you must connect a

separate copper grounding wire as

(#I8 minimum) to a grounded cold

water pipe* by means of a clamp and

then to the external grounding

connector screw. Do not connect the

power cord to outlet until the appliance

is permanently

grounded. See Figure 2.

Now Start...

With

Washer in laundry Area.

Remove tape that covers

shipping strap. Firmly jerk, then

pull to completely

remove the shipping

strap from the inside of the washer.

Remove the power cord from the

basket Peel the tape down and off

each side of cabinet.

PAGE 2