Whirlpool 3956025 Handleiding voor installatie-instructies - Pagina 2

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Whirlpool 3956025. Whirlpool 3956025 20 pagina's.

Pagina afdrukken

Tools and Parts

Assemble the necessary tools and supplies before beginning the

washer installation. The parts supplied are in the washer basket.

Tools needed for connecting the drain hose and

water inlet hoses:

Pliers that open to 1⁹⁄₁₆ in. (3.95 cm)

Flashlight (optional)

Parts supplied:

1. Drain hose

2. Silver, double-wire hose clamp

(for the bottom of the drain hose)

3. Yellow, single-wire hose clamp

(for the top of the drain hose)

4. Water inlet hoses (2)

5. Flat water inlet hose washers (4)

Tools needed for securing the drain hose and

leveling the washer:

Adjustable or open end wrench ⁹⁄₁₆ in. (14 mm)

Level

Wood block

Ruler or measuring tape

Parts supplied:

1. Shipping strap with fastener

2. Front leveling feet with nuts (2)

INSTALLATION REQUIREMENTS

Alternate Parts

Your installation may require additional parts. For ordering

information, please refer to the toll free phone numbers on the

front page of your "Washer User Instructions."

If You Have:

You Will Need to Buy:

Laundry tub or

Sump pump system (if not already

standpipe taller

available)

than 96 in. (2.4 m)

1 in. (2.5 cm)

2 in. (5 cm) diameter to 1 in. (2.5 cm)

diameter

diameter standpipe adapter, Part No.

standpipe

3363920

Overhead sewer

Standard 20 gal. (76 L) 39 in. (99 cm) tall

drain tub or utility sink, sump pump and

connectors (available from local

plumbing suppliers)

Floor drain

Siphon break, Part Number 285320;

additional drain hose, Part Number

3357090 and connector kit,

Part Number 285442

Water faucets

2 longer water fill hoses:

beyond reach of

6 ft (1.8 m) Part Number 76314,

fill hoses

10 ft (3.0 m) Part Number 350008

Drain hose too

Drain hose, Part No. 388423 and hose

short

kit, Part No. 285442

Drain hose that is

Hose kit, Part No. 285442

too long

Lint clogged drain

Drain protector, Part No. 367031

Location Requirements

Selecting the proper location for your washer improves

performance and minimizes noise and possible washer "walk."

Your washer can be installed in a basement, laundry room,

closet, or recessed area. (See "Drain System.")

IMPORTANT: Do not install or store the washer where it will be

exposed to the weather.

Proper installation is your responsibility.

You will need:

A water heater set to deliver 120°F (49°C) water to the

washer.

A grounded electrical outlet located within 4 ft (1.2 m) of

where the power cord is attached to the back of the washer.

(See "Electrical Requirements.")

Hot and cold water faucets located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of 5-100 psi

(34.5-690 kPa). Washers with triple dispensers require

20-100 psi (138-690 kPa) for best performance.

A level floor with a maximum slope of 1 in. (2.5 cm) under

entire washer. Installing the washer on carpeting is not

recommended.

A sturdy floor to support the washer weight (washer, water

and load) of 315 lbs (143 kgs).