Whirlpool 3XLBR5432JQ4 Installatie-instructies - Pagina 4
Blader online of download pdf Installatie-instructies voor {categorie_naam} Whirlpool 3XLBR5432JQ4. Whirlpool 3XLBR5432JQ4 5 pagina's. 120-volt 60-hz washer
Ook voor Whirlpool 3XLBR5432JQ4: Gebruiks- en onderhoudshandleiding (12 pagina's)
![Whirlpool 3XLBR5432JQ4 Installatie-instructies](/uploads/products/server2/6791980/6791980.png)
Drain
hose
ln|et hose
(to water
faucets)
1/4"
® To prevent the drain hose
from coming off or leaking,
it must be installed per the
following
instructions.
Wet the inside end of the drain
hose with tap water DO NOT USE
ANY OTHER LUBRmCANT.
Squeeze ears of drain hose clamp
with pliers to open and place
clamp over the end of the drain
hose.
Open clamp and push end of drain
hose onto drain connector until
hose contacts ribbed stop.
Place clamp over area marked
"clamp".
Release clamp.
e Standpipe
or
laundry
tub dra|n
system:
Open yellow damp and slide over
"hook"
end of drain hose
to secure the rubber
and corrugated
sections together.
F|oor drain
system:
Do Not instal[ "hook"
__
LD "_
end of drain hose to
corrugated
section. Consult your
plumber for proper installation.
Run wate_
through
i_'_'.' . _ R_,._
both faucets into
-
a bucket to get
rid of particles in the water lines
that might clog hoses. Mark the hot
water faucet.
Put "hook"
end of drain
® hose into laundry tub or
standpipe. Check for proper length
of drain hose.
To prevent
drain
water
from
going
bach
into
washer:
Do Not
straighten
"hooh"
end
of drain
hose and
force
excess
drain
hose
into
standpipe.
Do
Not
lay e×¢ess
drain
hose
in bottom
of laundry
tub.
Check inlet hoses
periodically.
Replace inlet
hoses if you find bulges,
kinks, cuts, wear or leaking.
Replace inlet hoses after
five years of use.
blots
are pBastk°
Do Not
strip
or
crossthread.
cold
water
inlet
valve
hot water
inlet valve
Attach bottom
hose from
® the inlet marked "H" to
the hot water faucet. Attach top
hose from the inlet marked "C" to
the cold water faucet. Tighten
couplings to faucets DO NOT
OVERTIGNTEN;
this could cause
damage to couplings.
® Stack two corner
posts
on top of each other
and postion
them
3 inches from
each side of
the washer.
Grasp the top, front
corners
of the washer
and tilt
backward
until
bottom,
front
of
washer
is 3-4 inches off the floor
and slide corner
posts under
washer
as shown.
1/2"
® Screw nut down on legs
to within 1/2 inch of base.
\
3e
Insert
legs into correct
holes at each front
corner
of washer
until
nuts touch
washer.
DO NOT
tighten
nuts until Step 16.
i Grasp top front
corners
to
tilt washer
backward
and remove
corner
post(s).
Gently
lower washer
to floor.
Use outside
corners
of the
cabinet
to
move
washer
to its
final
location.
Remove
cardboard
or hardboard
from
under
washer.
S
Tilt washer forward
® slightly so that back legs
are about 1 inch off floor. Drop
washer to floor. Check levelness of
the washer by placing a carpenter's
level on top of the washer, first side
to side; then front to back.
@
If washer is not level, repeat Step
11, and adiust the front legs up or
down. Then repeat Steps 14 E<15.
When
washer
is level, use
wrench
to turn
nuts on front
legs up tightIy
against
washer
base. |f nuts are not tkJht
against
washer
base, the
washer
may vibrate.
dra|n
hose:
NOTE:
Use shipping
strap to
secure drain
hose. Water pressure
could
cause drain
hose to come
out of standpipe
or laundry
tub if
drain
hose is not secured.
a
After shipping strap has been
removed (Step 1), look for the
words "cut here" marked on the
shipping strap, about 16 inches
from plug end
Cut the shipping strap at this
mark. Pull shipping strap out of
the power supply cord.
Check
that
hose
is not
twisted
or kinked
and
is securely
in
place.
B
Put "hook" end of drain hose in
laundry tub or standpipe. Tightly
wrap the shipping strap around the
drain hose and laundry tub or
standpipe as shown in Figures AoB.
Push plug into the nearest hole in
the shipping strap.
If the water inlet
faucets and drain
standpipe are
recessed, put
"hook"
end of
drain hose in
standpipe. Tightly
wrap the shipping
strap around the
drain hose and
strap
faucet body (not the handles or
stems) as shown in Figure C. Push
plug into the nearest hole in the
shipping strap.
D
i;'
:cs
If a Ion( er drain hose is needed, use
a 21" or 54" drain hose and
Connector Kit, Part No. 285442. If
drain hose must be shortened, use
Connector Kit Part No. 285442.
These parts are available from your
local dealer or authorized
parts
distributor.
Note:
|f washer
is moved
to
adjust
drain
hose,
the
washer
must
be IeveIe¢ tl again.
Repeat
Steps
1S°16.
Place
cardboard
under
the
washer
and
carefully
move
washer
to avoid
damacJin
9 floor
¢overin
9.
Panel C