Whirlpool 3XLBR8543 Gebruiks- en onderhoudshandleiding - Pagina 10
Blader online of download pdf Gebruiks- en onderhoudshandleiding voor {categorie_naam} Whirlpool 3XLBR8543. Whirlpool 3XLBR8543 13 pagina's. Two speed automatic washer
Ook voor Whirlpool 3XLBR8543: Gebruiks- en onderhoudshandleiding (35 pagina's), Handleiding voor installatie-instructies (11 pagina's), Gebruiks- en onderhoudshandleiding (40 pagina's)
Pagina afdrukken
Wa(,er5: le Hoses
Replace inlet hoses after five years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker•
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Non-uce
or vacation
care
Operate your washer only when you are at home. If you we, be on
vacation or not using your washer for an extended period of time.
you should:
=
Unplug washer or disconnect
power.
•
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
To winterize washer
1. Shut off both water faucets.
2.
Disconnect and drain w_erinlethoses.
3. Put I quart (1 L) of R.V.-type antifreeze in the basket.
4. Runwasheronadrainandspinsstting(see"DrainandSpin")
for about 30 seconds to mix the antifreeze and water.
5.
Unplug washer or disconnect power.
To use washer
again
1. Flush water pipes and hoses.
2.
Reconnect water inlet hoses.
3. Turn on both water faucets.
4. Plug in washer or reconnect power.
5.
Run the washer through a complete cycle with I cup (250 mL)
of detergent to clean out antifreeze.
TROUBLESHOOTING
Rrst try the solutions suggested here and possibly avoid
the cost of a service call...
Washer won't fill, rinse or agitate
=
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
l
Does the water level seem too low, or does the washer
appear to not fill completely?.
The top of the agitator is much higher than the highest water
level This creates a perception that the washer is not filling
completely, This is normal,
=
Is the lid open?
The lid must be closed during operation.
Washer •tops
•
Check the fallowing:
Is the power cord plugged into a grounded 3 prong outlet?
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
m Is there power at the plug?
Check your electrical source or call an electrician.
=
Has a fuse blown or is the circuit breaker open?
If problem continues, call an electrician.
Are you using an extension cord?
Do not use an extension cord.
Is the washer in a normal pause in the Synthetics/
Permanent Press (or Hand Washables) cycle?
The washer pauses for about 2 minutes in the Synthetics/
Permanent Press cycle. Allow the cycle to continue.
The Hand Washables cycle (on some models) features
periods of agitation and soak.
Is the washer overloaded?
Wash smaller loads.
Washer won't drain or spin
•
Is the drain hose clogged, or the end of the drain hose
more than 72 inches (183 cm) above the floor?
See the Installation Instructions for proper installation of drain
hose.
•
Is the lid open?
The lid must be closed during operation.
10