Whirlpool 3XLSQ7533 Gebruiks- en onderhoudshandleiding - Pagina 7
Blader online of download pdf Gebruiks- en onderhoudshandleiding voor {categorie_naam} Whirlpool 3XLSQ7533. Whirlpool 3XLSQ7533 13 pagina's. Two speed automatic washer
Ook voor Whirlpool 3XLSQ7533: Gebruiks- en onderhoudshandleiding (35 pagina's), Handleiding voor installatie-instructies (11 pagina's), Gebruiks- en onderhoudshandleiding (40 pagina's)
Pagina afdrukken
6.
Set the TEMPERATURE selector to the correct setting for the
type of fabric and soils being washed. Use the warmest water
safe for fabric. Follow garment label instructions.
Your washer uses automatic temperature control (on some
models) to maintain a uniform water temperature by
regulating the incoming hot and cold water. This helps
eliminate undissolved detergent and ensures consistent
cleaning results. The cold wash is regulated at approximately
75°F (24°(3) by adding small amounts of hot water during the
cold fill. The warm wash is maintained at approximately
100°F (38°C).
NOTE: Make sure that both the hot and cold water taps are
fully turned on or the automatic temperature control feature
will not work properly.
Water Temp
Use For
Hot
Whites and pastels
111°F (44°C)
Heavy and greasy soils
or above
Warm
Bright colors
90°-110°F
Moderate to light soils
(32°-43°C)
Cold
Colors that bleed or fade
70°-90°F
Light soils
(21 °-32°C)
i
,111, .......
NOTE: In wash water temperatures colder than 70°F
(21°C), detergents do not dissolve well. Soils can be difficult
to remove. Some fabrics can retain wear wrinkles and have
increased pilling (the formation of small lint-like balls on the
surface of garments).
7.
(OPTIONAL) Some models have an EXTRA RINSE selector.
For an additional rinse and spin at the end of a wash cycle,
set the EXTRA RINSE selector to ON. On some models, the
Extra Rinse feature is part of the cycle.
8.
(OPTIONAL) Some models have an END OF CYCLE SIGNAL
selector. Set the END OF CYCLE SIGNAL selector to ON if
you want your washer to alert you when the wash cycle is
complete. The signal is helpful when you are washing items
that should be removed from the washer as soon as the cycle
ends.
9, Push in the Cycle Control knob and turn it clockwise to the
wash cycle you want. Reduce the wash time when using a
small load size setting. See "Selecting a Cycle and Time."
Pull out the Cycle Control knob to start the washer.
To stop or restart your washer
a
To stop the washer at any time, push in the Cycle Control
knob.
=
To restart the washer, close the lid (if open) and pull out
the Cycle Control knob.
Adding bleach to models without a bleach dispenser
If desired, add measured liquid chlorine bleach after the washer
starts agitating. Pour diluted bleach around the agitator, not
directly on the load. Undiluted bleach will damage any fabric it
touches. (See "Adding Liquid Chlorine Bleach.")
Adding softener
to models without
a fabric softener
dispenser
If desired, add measured liquid fabric softener to the final rinse
water. Always dilute fabric softener with _,_ to t cup (125 to
250 mL) cup of warm water. Undiluted fabric softener can stain
fabrics. (Sea "Adding Liquid Fabric Softener.")
The control panel of your washer contains symbols.
Refer to the
chart below for a definition of those symbols.
Symbols
Symbols
Small Load
Hand Washables
Large Load
• _•
Super Wash
":9:-
Cold
Wash
Temperature
Warm
Quick Wash
•|a
Temperature
-;O_R
Hot
Prewash
Temperature
___
Temperature
_
Rinse
(3
IIHm
HHm
mH
On
r--_--
Extra Rinse
I
mmmmm=lu
iiiii
_
mll
© o.
@Spin
Buzzer
@
Slow Spin
Cotton
Cool Down
Pull Start
Synthetics
_3 _)
Push Stop
Delicates
7