Whirlpool 6ALSR7244MW3 Gebruiksaanwijzing - Pagina 5

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Whirlpool 6ALSR7244MW3. Whirlpool 6ALSR7244MW3 8 pagina's. Whirlpool 6alsr7244mw3 washer user instructions

Pagina afdrukken

First try the solutions suggested here and possibly avoid the cost of a service call.

Washer and Components

Noisy

Is the load balanced and the washer level? The wash load

should be balanced and not overloaded. The washer must be

level. The front feet should be properly installed and the nuts

tightened. Reset the rear leveling legs (if needed). See the

Installation Instructions.

Did you completely remove the yellow shipping strap with

cotter pins? See the Installation Instructions.

Are the gears engaging after the drain and before spin, or

is the upper part of agitator clicking during wash? These

are normal washer noises.

Leaking

Check the following:

Are the fill hoses tight?

Are the fill hose washers properly seated?

Is the drain hose clamp properly installed? See the Installation

Instructions.

Is the sink or drain clogged? Sink and standpipe must be

able to handle 64 l (17 gal.) of water per minute.

Is water deflecting off the tub ring or the load? Center the

tub before starting the washer. The wash load should be

balanced and not overloaded. The fill or spray rinses can

deflect off the load. The washer must be level. The front feet

should be properly installed and the nuts tightened. Reset the

rear leveling legs (if needed). See the Installation Instructions.

Check household plumbing for leaks.

Basket crooked

Was the washer basket pulled forward during loading?

Push the basket to the center before starting wash.

Is the load balanced and the washer level? The wash load

should be balanced and not overloaded. The washer must be

level. The front feet should be properly installed and the nuts

tightened. Reset the rear leveling legs (if needed). See the

Installation Instructions.

The washer basket moves while washing. This is normal.

Agitator operation

The top of the agitator is loose, or moves in only one

direction. This is normal.

Dispensers clogged or bleach leaking

Did you follow the manufacturer's directions when adding

detergent and fabric softener to the dispensers (on some

models)? Measure detergent and fabric softener. Slowly pour

into the dispensers. Wipe up all spills. Dilute fabric softener in

the fabric softener dispenser.

Did you put powdered or color-safe bleach in the liquid

chlorine bleach dispenser (on some models)? Add

powdered or liquid color-safe bleach directly to the basket. Do

not use the chlorine bleach dispenser for color-safe bleach.

TROUBLESHOOTING

Washer stops, won't fill, rinse or agitate

Check the following:

Is the power cord plugged in?

Is the indicator on the Cycle Control knob properly lined up

with a cycle? Turn the Cycle Control knob to the right slightly

and pull to start.

Are the water inlet valve filters clogged?

Are both the hot and cold water taps turned on?

Is the water inlet hose kinked?

Does the water level seem too low, or does the washer

appear to not fill completely? The top of the agitator is much

higher than the highest water level. This is normal and

necessary for clothes to move freely.

Has a fuse blown or is the circuit breaker open? If problem

continues, call an electrician.

Are you using an extension cord? Do not use an extension

cord or an electrical portable outlet device.

Is the washer in a normal pause in the cycle? The washer

pauses for about 2 minutes during certain cycles. Allow the

cycle to continue. Some cycles feature periods of agitation

and soak.

Is the washer overloaded? Wash smaller loads.

Is the lid open? The lid must be closed during operation.

Washer will not agitate or spin with the lid open.

Washer won't drain or spin

Is the drain hose clogged, or the end of the drain hose

more than 183 cm (72") above the floor? See the Installation

Instructions for proper installation of drain hose.

Is the lid open? The lid must be closed during operation.

Washer will not agitate or spin with the lid open.

Is there excessive sudsing? Always measure detergent.

Follow manufacturer's directions. If you have very soft water,

you might need to use less detergent.

Washer continues to fill or drain, cycle seems stuck

Is the top of drain hose lower than the water level in

washer? The top of the hose must be higher than the water

level in the washer for proper operation. See the Installation

Instructions.

Does the drain hose fit too tightly in the standpipe, or is it

taped to the standpipe? The drain hose should be loose yet

fit securely. Do not seal the drain hose with tape. The hose

needs an air gap. See the Installation Instructions.

Washer Operation