Whirlpool 8182192 Gebruiks- en onderhoudshandleiding - Pagina 18
Blader online of download pdf Gebruiks- en onderhoudshandleiding voor {categorie_naam} Whirlpool 8182192. Whirlpool 8182192 44 pagina's. Front-loading automatic washer
Pagina afdrukkenTROUBLESHOOTING
First try the solutions suggested
hers to possibly avoid the
cost of a service call...
Washer displaying
code message
and tone sounds
•
"FH" (Water Inlet Problem--no
water or insufficient water
supply)
Select PAUSE/CANCEL twice to cancel the cycle. Unplug
washer or disconnect
power.
Check the following:
Are water faucets completely turned on?
Are screens at inlet hose connection to washer clogged?
Are water inlet hoses kinked?
Are water inlet hoses frozen?
Plug in washer or reconnect power. Re-select cycle and press
HOLD TO START. If the problem remains, call for service.
•
"F02" (Drain Problem)
Select PAUSE/CANCEL twice to cancel the cycle. Unplug
washer or disconnect
power.
Check the following:
Is the drain hose kinked?
Is the drain hose frozen?
Is the drain hose clogged?
Is the drain hose more than 96 in. (2.4 m) above the floor?
•
"SUB" (Suds Routine)
When excessive suds are detected, a suds routine
automatically
starts. This routine removes extra suds and
assures proper rinsing of your garments. "SUD" is displayed
during rinsing and at the end of the cycle to inform you that
Suds Routine was activated. To avoid excessive sudsing,
use only HE detergents.
•
"F" Variables [F4 to F16] (Electrical Problem)
Select PAUSE/CANCEL twice to cancel the cycle. Select
DRAIN/SPIN if there is excessive water in the washer.
Re-select cycle and press HOLD TO START. If the problem
remains, call for service.
Washer won't start
•
Checkthe
following:
Is the power cord plugged into a grounded 3 prong outlet?
Is the washer door firmly closed?
Has a cycle been selected, but HOLD TO START has not
been selected and held for one second?
Was the door open after completion
of last cycle?
Washer won't fill, wash or rinse
•
Checkthe
following:
Is the power cord plugged into a grounded 3 prong outlet?
Is there power at the plug? Check electrical source or call
electrician.
Are the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Washer stops
•
Checkthe
following:
Is the power cord plugged into a grounded 3 prong outlet?
Is there power at the plug?
Check electrical source or call electrician.
Has a fuse blown or has the circuit breaker tripped?
If problem continues, call electrician.
Are you using an extension cord?
Do not use an extension cord.
Washer won't drain or spin
•
Is the drain hose clogged, or the end of the drain hose
more than 96 in. (2.4 m) above the floor?
•
Is your voltage low?
Check electrical source or call electrician. Do not use an
extension cord.
•
Is the "SUD" routine active?
Cycle will complete once extra suds are removed.
•
Is the load balanced?
A single or bulky item may cause imbalance. Add more items
or redistribute the load.
Washer makes noise or vibrates
Is the washer level?
The washer must be level. The four feet should be properly
installed, and the nuts should be tightened against the
washer cabinet.
As water is drained from the washer, you may hear air being
pulled through the pump. This happens during the end of
draining. It is normal.
Are you washing items with metal snaps, buckles or
zippers?
You may hear metal items touching the washer drum. This is
normal.
Is washer installed
on a sturdy and solid floor?
Refer to the "Installation
Instructions" for flooring
requirements. Noise and vibration may be reduced by placing
a piece of 3Ain. (19.1 ram) plywood underneath your washer.
The plywood may extend underneath both washer and dryer
to keep them at equal heights.
Washerleaks
•
Check household plumbing
for leaks.
Are the water inlet valve screens clogged?
18