Whirlpool AWM 9100 Programmakaart - Pagina 2

Blader online of download pdf Programmakaart voor {categorie_naam} Whirlpool AWM 9100. Whirlpool AWM 9100 3 pagina's.

Pagina afdrukken
CONSUMPTION DATA
Temperature
Programme
°C
Sanitary
Max
White Cotton
60
Heavy Duty
60
Normal/Casual
60
Express Wash
40
Delicate
40
Silk
30
Wool
30
Ultra Handwash
30
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the
values in the table dependent on the water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the
household conditions applicable at that time.
ADD DETERGENT, CLOSE THE DOOR AND
SELECT THE PROGRAMME
Add the detergent as described in the programme table
or in the chapter "Detergent and Additives" of the
instructions for use.
1. Press the desired wash cycle.
2. The remaining time display shows the duration of
the chosen programme (in hours and minutes) and
the pilot lamp of the wash cycle button lights up.
3. The programme sequence, the predefined spin
speed, water temperature, End of Cycle signal and
options indicators corresponding to the selected
programme light up.
The recommendations can be altered by pressing the
modifier and the option buttons.
SELECT ANY DESIRED OPTION AND
MODIFIER
Selecting any option the indication lights up.
When the combination of programme, additional
options and modifiers is not possible, the indication
lights switch off automatically and a signal sounds.
"Prewash"
• For heavily soiled laundry.
• The cycle time increases approx. 15 minutes.
• Add detergent to the Prewash and Main Wash
dispenser compartments.
• When using the Prewash compartment, do not use
liquid detergent in the Main Wash compartment:
use powder detergent for the main wash cycle.
Load
Water
Approximate programme
duration*
(kg)
(l)
(hours : minutes)
9.0
90
2:15
9.0
84
1:55
9.0
84
2:10
3.5
50
1:20
2.0
48
0:45
2.5
65
0:55
2.0
60
0:35
2.0
60
0:40
2.0
60
0:40
• "Prewash" and "Auto Soak" options cannot be
selected in the same cycle.
"Stain Treat"
• For heavily soiled laundry.
• Warm water fill for optimal organic soil removal and
heat to high temperature.
"Auto Soak"
• For heavily soiled laundry with set-in stains.
• The cycle time increases approx. 30 minutes.
• Use with a wash cycle:
Select the desired wash cycle and the "Auto Soak"
option, add detergent to the Prewash and the Main
Wash dispenser compartments; press the "Start"
button. When using the Prewash compartment, do not
use liquid detergent in the Main Wash compartment:
use powder detergent for the main wash cycle.
• Use without a wash cycle:
Select first "Drain/Spin" or "Rinse/Spin" and then
"Auto Soak" option; choose the desired soak
temperature, add detergent to the Prewash
compartment and press the "Start" button.
• "Prewash" and "Auto Soak" options cannot be
selected in the same cycle.
"2nd Rinse"
• This option is recommended to ensure the removal
of detergent or bleach residues from garments.
• It provides an additional rinse with the same water
temperature as the first rinse.
• This option is particularly suitable for areas with
very soft water, for baby clothes and to help people
with allergies.
"Extended Spin"
• This option is useful for adding an additional spin
to any cycle to improve the "fluff" of your
laundry, to reduce drying time and to save energy
"Modifiers"
Preset cycle settings of water temperature (wash
temperature/rinse temperature), spin speed (0 to
1000), End of Cycle signal (off, low or high) and soil
level (light, normal, heavy) can be changed. You can
modify the settings by pressing the respective buttons.
Changing the soil level leads to different programme
durations.
START DELAY
The "Start Delay" allows to run the machine at the
consumer's convenience, for example at night when
electricity may be cheaper.
• Select programme, modifier and options.
• Press the "Start Delay" button to select the delay
time by 1 to 10 hours;
• Press the "Start" button for at least 2 sec.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining time.
• The number of hours preselected can later be
reduced pressing again the "Start Delay" button.
To cancel the "Start Delay".
• Press the "Pause/Reset" button once.
• Press the "Start Delay" button up to 00 h in the
display.
•
Check the programme setting and press and hold
the "Start" button.
PROGRAMME START
Turn on the tap(s) and press the "Start" button for
a few seconds.
The indicator lamps show the sequence reached in
the programme. After starting the programme, the
sequence indication runs from top to bottom through
"Add a Garment"
, "Soak/Prewash"
,
"Wash"
, "Rinse"
, "Spin"
and "End of
Cycle"
.
When a sequence of the programme is finished the
corresponding lamp goes out.
ADD A GARMENT
After programme start and while the "Add a
garment" lamp is on you can still add a garment.
Press "Pause/Reset" button once. After few seconds
the door will be unlocked and you can add the item.
Close the door and press the "Start" button again.
The programme will run again from the point where
it was interrupted.
DOOR LOCK
After each programme start the door is locked and
approx. 0.5 l of water is rinsed in. The door is
unlocked for a few seconds. The door is then locked
until the end of the programme. Detailed information
can be found in the instructions for use.
PROGRAMME END
• The time remaining is "0:00", the "End of Cycle"-
light is on and a signal sounds, if selected.
1. Take out the load.
2.
Turn the tap off and leave the door ajar to allow
the drum to dry out.
The control panel is switched off 5 minutes after the
end of the cycle, it is still possible to open the door.
CHANGE THE PROGRAMME,
TEMPERATURE, OPTIONS AFTER
PROGRAMME START
1. Press the "Pause/Reset" button once to interrupt
the programme. The light flashes.
2. Select the new programme with temperature,
any options and modifier if you want.
3.
Press the "Start" button. The new programme
continues at the same position where the
previous programme was interrupted. Do not
add detergent for this programme.
CANCEL A PROGRAMME BEFORE THE END
Press the "Pause/Reset" button twice. Any existing
water is drained out before the door can be opened.
LOCKING CONTROLS
The "Controls Locked"
prevents unintended use
of the washer. You can also use the "Controls
Locked"
feature to prevent unintended cycle or
option changes during a cycle. When "Controls
Locked" is lit, all buttons are disabled. You can lock
the washer while it is operating.
To lock the controls:
Select and hold "Drain/Spin"
button for 3
seconds. The "Controls Locked" status indicator
lights up.
To unlock the controls:
Select and hold "Drain/Spin"
button for 3
seconds until the "Controls Locked"
status
indicator is switched off.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 15169