Ariston ASL 75 CXS NA Handleiding voor verzorging, gebruik en installatie - Pagina 6
Blader online of download pdf Handleiding voor verzorging, gebruik en installatie voor {categorie_naam} Ariston ASL 75 CXS NA. Ariston ASL 75 CXS NA 40 pagina's. Condensation dryer
Ook voor Ariston ASL 75 CXS NA: Gegevensblad (1 pagina's), Brochure & specificaties (8 pagina's), Gebruiks- en installatiehandleiding (40 pagina's), Reparatiehandleiding (18 pagina's)
Pagina afdrukken
Start and Programs
The Controls
EN
PROGRAMS knob
! Warning, if after pressing the start button, the
programs knob position is changed, the new position
will NOT change the program selected.
! Position 0, turning the programs knob to position 0
resets and cancels a program.
OPTION buttons / lights
These buttons are used to customize the selected
program to your requirements. A program must have
been selected on the programs knob before an option
can be selected. Not all options are available for all
programs (see Start and Programs). If an option is not
available and you press the button, the buzzer will
beep four times. If the option is available there will be
one beep and the option light next to the button lights
to confirm the selection.
Progress (Drying, Air Fluff, Post Creasecare) /
Delay (3hr 6hr 9hr 12hr) Lights
When the light next to the delay button is on, these lights
flash to indicate the delay time is selected. During other
programs they indicate the progress of the dryer, each
one comes on as the corresponding phase starts.
Time Delay
The start of some programs (see Start and Programs)
can be delayed for up to 12 hours in 3hr steps.
When a delayed start is in progress the light next to the
delay button will be on and the selected delay period
light will flash (after the start button has been pressed).
To set a delayed start, press the Time Delay button,
and the light next to the button will come on together
with the 3hr delay light. Pressing the button again will
advance the delay setting to 6hr, the 3hr light goes
out and the 6hr light is on. Each time you press the
button the delay setting advances 3 hours, as indicated
by the corresponding light. If the 12hr light is on,
pressing the button again will cancel the delay.
You can also cancel the delay by turning the programs
knob to 0, wait for the buzzer to beep and then turn
back to your selected program.
Pre Creasecare
When a delayed start has been selected, the clothes
are tumbled occasionally during the delayed period to
help prevent creases developing.
www.aristonappliances.us
6
High Heat
When available this button selects high heat. Press this
button and a high heat setting is selected and the light
next to the button comes on. Timed programs have a
default to low heat. If the light alongside the button is
on then pressing the button selects a low heat setting
and the light goes out.
Alarm
Available on all programs and allows the buzzer to
give a signal at the end of the drying cycle, to remind
you that the clothes are ready to be removed.
Press the button and the light will show that the option
is selected.
Post Creasecare
The clothes are occasionally tumbled after the end of
the drying and air fluff cycles to help prevent creases
developing should you not be available to remove the
load immediately the program is complete.
Door Opening
Opening the door during a program will stop the dryer
and have the following effects:
All 3 progress lights and the 3hr delay light come
on.
During a delay phase the delay will continue to
count down. The start button must be pressed to
resume the delay program.
One of the delay lights will flash to show the
current delay setting.
The start button must be pressed to resume the
program. The progress lights will change to show
the current status.
During the air fluff or post creasecare phase of a
drying program and anytime during an Airing or
Air Fluff program, the program will finish. Pressing
the start button will re-start a new program at the
beginning.
Changing the programs knob will select a new
program, after you press the start button. You can
use this to select the Air Fluff program to cool the
clothes, if you find them dry enough.
Note
If you have a power outage, switch off the power or
remove the plug, press the START button and the
program will resume.