Whirlpool 8527813 Handleiding voor installatie-instructies - Pagina 5

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Whirlpool 8527813. Whirlpool 8527813 13 pagina's. Commercial stacked dryer gas & electric

Pagina afdrukken

Check that dryer is equipped

with the correct burner for the

particular type of gas used. Burner

information can be found on the

serial/rating plate in the door well of

the appliance. If this information does

not agree with the type of gas

available, see your dealer.

This dryer is equipped for use

with NATURAL GAS. It is certified by

CSA International for L.P. (propane

and butane) gases with appropriate

conversion. No attempt shall be

made to convert the appliance from

the gas specified on the serial/rating

plate for use with a different gas

without consulting the serving gas

supplier. Conversion must be done by

a qualified service technician. Gas

conversion kit part numbers are listed

on the gas valve burner base.

Provide a rigid gas supply line of

1/2-inch IPS pipe or 1/2-inch

approved tubing to the dryer

location. If the total length of the

supply line is more than 20 feet

(6.1 m), larger tubing will be needed.

Pipe-joint compounds suitable for use

with L.P. gas should be used.

shutoff valve

"open" position

to dryer

The supply line shall be equipped

with a shutoff valve installed within

6 ft. (1.8 m) of dryer in accordance

with the National Fuel Gas Code,

ANSI Z223.1 — latest edition*. This

valve should be located in the same

room as the dryer and should be in a

location that allows ease of opening

and closing. Do Not block access to

the shutoff valve.

If the dryer is installed in a

confined area such as a bathroom or

closet, provision must be made for

enough air for combustion and

ventilation. (Check governing codes

and ordinances. or refer to the

section of this instruction covering

recessed and closet installations.)

If local codes and ordinances

permit, it is recommended that a new

flexible gas connector, design-

certified by the AGA or CSA, be used

for connecting the dryer to the gas

supply line. (The gas pipes which

extend through the rear of the dryer

are 3/8-inch pipe thread.)

If rigid

pipe is used

as a gas supply line, a

combination of pipe fittings must

be used to obtain an in-line

connection to the dryer.

For ease of installation,

operation and servicing, adequate

space should be provided around

the dryer.

A 1/8-inch NPT plugged

tapping, accessible for test gauge

connection, must be installed

immediately upstream of the gas

supply connection to the dryer.

The dryer must be disconnected from

the gas supply piping system during

any pressure testing of the system at

test pressures in excess of 1/2 psig.

The dryer must be isolated from the gas

supply piping system by closing the

equipment shut-off valve during any

pressure testing of the gas supply piping

system at test pressures equal to or less

than 1/2 psi (3,45 kPa)

Electrical

requirements

gas supply

line

Electrical Shock Hazard

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions

can result in death, fire, or electrical

shock.

Important: Observe all governing

codes and ordinances.

A 120-volt, 60-Hz, AC-only, 15- or

20-ampere fused electrical supply is

required. A time-delay fuse or circuit

breaker is recommended.

It is recommended that a separate

circuit serving only this appliance be

provided.

If codes permit and a separate ground

wire is used, it is recommended that a

qualified electrician determine that the

ground path is adequate.

WARNING

Recommended

ground method

The dryer, when installed, must be

electrically grounded in accordance

with local codes, or in the absence of

local codes, with the National

Electrical Code, ANSI/NFPA 70*.

GROUNDING INSTRUCTIONS: This

appliance must be grounded. In the

event of malfunction or breakdown,

grounding will reduce the risk of

electric shock by providing a path of

least resistance for electric current.

The power supply cord plug must be

plugged into an appropriate outlet

that is properly installed and

grounded in accordance with all

local codes and ordinances.

WARNING - Improper connection of

the equipment-grounding conductor

can result in a risk of electric shock.

Check with a qualified electrician or

serviceman if you are in doubt as to

whether the appliance is properly

grounded. Do not modify the plug

provided with the appliance - if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

3-prong ground-type

outlet

3-prong

ground

plug

power

ground

supply cord

prong

Copies of the standards listed above may

be obtained from:

* National Fire Protection Association

One Batterymarch Park

Quincey, Massachusetts 02269

Page 5