Whirlpool CEM2750JQ0 Installatiehandleiding - Pagina 6

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Whirlpool CEM2750JQ0. Whirlpool CEM2750JQ0 14 pagina's. Commercial gas/electric dryer

Pagina afdrukken

Now Start...

With dryer in laundry area.

Excessive Weight Hazard

Use two or more people to move end

install dryer.

Failureto do se can result in beck or

other injury.

3-prong,

ground-type

gas supply line

gas shutoff valve

a Take tape off front corners of

dryer. Open dryer and remove the

literature and parts packages. Wipe

the interior of the drum thoroughly

with a damp cloth.

mTake two of the cardboard

corners from the carton and place

them on the floor in back of the dryer.

Firmly grasp the body of the dryer

and genfiy lay it on its back on the

cardboard

corners.

wWith one of the legs in hand,

check the ridges for a diamond

marking. That's how far the leg is

supposed to go into the hole.

i Start to screw the leveling legs

into the holes by hand. (Use a small

amount of liquid detergent to

lubricate the screw threads so it is

easier to turn the legs.) Use a 1-inch

wrench or socket wrench to finish

turning the legs until you reach the

diamond mark.

Now stand the dryer up,

Slide dryer onto cardboard or

hardboard before moving across floor

to avoid damaging floor covering,

m Remove

the service door of the

meter

case, Lift

the service door

up at the back

and remove,

install money-

accepting

device,

(Refer to

manufaturer's

instructions

for proper

installation.)

For dryers using coin slides, use

adapter

kit supplied

with dryer.

Replace

the meter

case service door.

Put the coin vault with lock and key

the meter case opening,

• Move

dryer close to final

position.

Remove

cardboard

hardboard

from under dryer.

• Remove red cap from gas pipe.

Carefully

move dryer into final

position.

Place level on top of the

dryer, first side to side; then front to

back,

If the dryer is not level, adjust

the legs of the dryer up or down

until

the dryer is level.

• Connect

gas supply to dryer.

Use pipe-joint

compound

resistant to

the action

of L.P, gas for gas

connections,

if flexible metal

tubing

used, be certain

there are no kinks,

If necessary

for service,

open the toe

panel,

use a putty knife to press on

the toe panel

lock located

at the

center

top of the toe panel

Pull

downward

on the toe panel

to open.

Toe panel

Is hinged

at the bottom.

Open

the shutoff valve in the

gas supply line.

lOre

Use a non-corrosive leak

detection

fluid to check

for leaks.

Bubbles around

connections

will

indicate

a leak, NEVER lEST FOR GAS

LEAKS WITH A FLAME. If a leak

appears,

shut off gas valve controls

and adjust connections.

Then check

connections

again.

Close toe panel

All connections

must be wrench-

tightened.

TO exhaust dryer, see Exhaust

requirements,

Pages 3-4. Connect

exhaust

vent system to dryer exhaust

outlet

and exhaust

hood using 4"

(10.2 cm) clamps,

Use caulking

seal exterior wall opening

around

exhaust

hood.

Carefully

move

dryer into

final position.

Place level on top of

the dryer, first side to side; then front

to back.

If the dryer is not level, adjust

the legs of the dryer up or down until

the dryer is level.

• Plug power

supply cord

Into

grounded

outlet.

• Check dryer operation

(some

accumulated

time may be on the

timer due to factory

testing).

Insert coins in slide and press slide in

slowly. (Operating

time win

accumulate

per number

of coins and

1ype of timing cam used.) Push

START/RESTARTbutton.

Using a full

heat cycle

(not the air cycle),

let the

dryer run for at least five minutes.

Dryer will stop when time is used up.

Note: Dryer door must be closed for

dryer to operate.

When door is open,

dryer stops, but fimer continues

to run.

To restart dryer, close door and bush

START/RESTARTbutton.

• ff fhe burner does not ignite

and you can feel no heat inside 1he

dryer, shut off dryer for five minutes.

Check

that all supply valve controls

are in "ON" position

and that the

elecfrical

cord is plugged

in. Repeat

five-minute

test,

6•

If drying time is too long,

make sure lint screen is clean.

Page 6