Whirlpool WGD96HEAC0 Gebruiks- en onderhoudshandleiding - Pagina 15
Blader online of download pdf Gebruiks- en onderhoudshandleiding voor {categorie_naam} Whirlpool WGD96HEAC0. Whirlpool WGD96HEAC0 40 pagina's. Electronic dryer
Pagina afdrukken
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help
-
"_
In Canada www.whirlpool.ca
for assistance and to possibly avoid a service call.
Door not closed completely.
Make sure the dryer door is closed completely.
START/PAUSE not touched firmly
Touch and hold START/PAUSE 2-5 seconds.
or held long enough.
Household fuse is blown or circuit
There may be 2 household fuses or circuit breakers for the
breaker has tripped,
dryer. Check that both fuses are intact and tight, or that both
circuit breakers have not tripped. Replace the fuses or reset the
circuit breaker, ff the problem continues, call an electrician.
hcorrect
power supply.
Electric dryers require 240-volt power supply.
Check with a qualified electrician.
Wrong type of fuse.
Use a time-delay fuse.
Dryer will not heat
Household fuse is blown or circuit
The drum may be turning, but you may not have heat. Electric
breaker has tripped,
dryers use 2 household fuses or circuit breakers. Replace the
fuses or reset the circuit breaker, ff the problem continues, call
an electrician.
hcorrect
power supply.
Electric dryers require 240-volt power supply.
Check with a qualified electrician.
Supply line valve not open.
If you experience
Dryer will not run
For gas dryers, make sure that the valve on the gas supply line
is open.
Humming or whining
noise with Steam cycle
selected
Thumping noise
Rattling or vibrating
noise
Clicking noise
Water pump on dryer is running.
Dryer hasn't been used in a while.
A small object caught between the
edges of dryer drum.
Dryer isn't properly leveled.
Clothing is balled up in dryer.
Gas valve operating.
The water pump on the dryer is used during the Steam function.
ff the dryer has just been installed or unused for an extended
period, the pump may be louder and run longer. This is normal.
This is normal. The thumping sound should diminish after a few
minutes of use.
Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.
The dryer may vibrate if not properly installed. See the
hstallation
hstructions.
All four dryer feet should be in firm
contact with the floor.
When balled up, the load will bounce, causing the dryer to
vibrate. Separate the load items and restart the dryer.
On gas dryers, you may hear the gas valve clicking as it opens
and closes. This is normal.
Clothes are not drying
Lint screen is clogged with lint.
Clean lint screen before each load.
satisfactorily
or drying
times are too long
The exhaust vent or outside
Run the dryer for 5-10 minutes. Hold your hand under
exhaust hood is clogged with lint,
the outside exhaust hood to check air movement. If you
restricting air movement,
do not feel air movement,
clean exhaust system of lint
or replace exhaust vent with heavy metal or flexible metal vent.
See the Installation Instructions.
The exhaust vent is not the correct
Check that the exhaust vent is not too long or has
length,
too many turns. Long venting will increase drying times.
See the Installation Instructions.
The exhaust vent diameter is not
Use 4" (102 mm) diameter vent material.
the correct size.
The dryer is not level.
Clothes not contacting the moisture sensors during Automatic
cycles. See "Level Dryer" in the Installation Instructions.
The Air Only temperature
setting
Select the correct temperature for the types of garments
has been selected,
being dried. See "Cycle Guide."
15