Whirlpool 30 " Eye-Level Gas Range Installatie-instructies en gebruiks- en onderhoudshandleiding - Pagina 5

Pagina afdrukken

For the most efficient and quiet operation:

Use no more than three 90° elbows.

Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

Do not install 2 elbows together.

Use clamps or duct tape to seal all joints in the vent system.

The vent system must have a damper. If roof or wall cap has a

damper, do not use damper supplied with the range hood.

Use caulking to seal exterior wall or roof opening around the

cap.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent System

Vent Piece

45° elbow

90° elbow

3¹⁄₄" x 10" (8.3 cm x

25.4 cm) flat elbow

7" (17.8 cm) wall cap

3¹⁄₄" x 10" (8.3 cm x

25.4 cm) to 7" (17.8 cm)

3¹⁄₄" x 10" (8.3 cm x

25.4 cm) to 7" (17.8 cm)

90° elbow

2.5 ft

(0.8 m)

5.0 ft

(1.5 m)

12.0 ft

(3.7 m)

0.0 ft

(0.0 m)

4.5 ft

(1.4 m)

5.0 ft

(1.5 m)

Example vent system

90˚ elbow

2 ft (0.6 m)

1 - 90° elbow

1 - wall cap

8 ft (2.4 m) straight

System length

Maximum Recommended Length

7" (17.8 cm) Round Vent

3¹⁄₄" x 10" (8.3 x 25.4 cm)

Rectangular Vent

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the range hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

Wall cap

6 ft (1.8 m)

= 5.0 ft (1.5 m)

= 0.0 ft (0.0 m)

= 8.0 ft (2.4 m)

= 13.0 ft (3.9 m)

= 50 ft (15.2 m)

= 35 ft (10.7 m)