Whirlpool 36'' Freestanding Gas Range Handleiding voor installatie-instructies - Pagina 6

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Whirlpool 36'' Freestanding Gas Range. Whirlpool 36'' Freestanding Gas Range 10 pagina's. 30" and 36" gas sealed burner cooktop
Ook voor Whirlpool 36'' Freestanding Gas Range: Handleiding voor installatie-instructies (13 pagina's), Handleiding voor installatie-instructies (7 pagina's), Handleiding voor installatie-instructies (7 pagina's), Installatie-instructies en gebruiks- en onderhoudshandleiding (28 pagina's), Handleiding voor installatie-instructies (28 pagina's), Handleiding voor installatie-instructies (6 pagina's), Handleiding voor installatie-instructies (7 pagina's), Installatie-instructies (5 pagina's)

Whirlpool 36'' Freestanding Gas Range Handleiding voor installatie-instructies

Check operation

E
Check operation of cooktop
17.
Push in and turn each surface unit
control knob to "LIGHT" position. The flame
should light within 4 seconds. Turn control
knob to desired setting after burner lights.
Check each cooktop burner for proper flame.
The small inner cone should have a very
distinct blue flame 1/4" to 1/2" long.
The outer cone is not as distinct as
the inner cone. If the flame is noisy
or blowing, it is getting too much
air. If the flame is soft and lazy, it is
not getting enough air. Turn each
surface burner control knob to
"OFF" position. Adjust air shutter if
needed.
If pilot light does not stay lit, adjust pilot
adjustment screw (see Step 15, Page 5).
If surface burners need adjusting:
1. Adjust the air shutter for each burner by hand
as needed. Close the air shutter to decrease
the amount of air to the flame. Open the air
shutter to increase the amount of air to the
flame. Adjust the air shutter to the widest
opening that will not cause the flame to lift or
blow off of the burner.
2. Repeat the first part of Step 17 after adjusting
the air shutters.
Page 6
Check operation of
oven/broil burner
18.
Open broiler drawer.
Push in and turn the oven control knob to
"350˚F." The oven pilot should now be larger
with the flame burning against a small metal
bulb. The oven burner should light in 20-40
seconds; this delay is normal. The oven valve
requires a certain time before it will open and
allow gas to flow.
The oven burner will burn until oven
temperature has reached 350°F. At that
temperature, the oven pilot should get smaller.
After 20-40 seconds, the oven burner will begin
to cycle on and off to maintain the 350°F
temperature.
19.
Check the oven burner
for proper flame. The flame should be
1/2" long, with inner cone of bluish-
green, and outer mantle of dark blue,
and should be clean and soft in
character. No yellow tips, blowing or lifting of
flame should occur. If burner does not light,
air shutter
check that the regulator shutoff valve is in the
"on" position (see Step 12).
air shutter
If oven flame needs adjusting:
Locate the air shutter next to the pressure
regulator. Loosen shutter screw and adjust the
air shutter until the proper flame appears.
Tighten shutter screw.
20.
Close the broiler drawer. Turn the
oven control knob to "OFF".
You have just finished installing
your new range. To get the most
efficient use from your range,
read your Use & Care Guide.
Keep Installation Instructions and
Guide close to range for easy
reference. The instructions will
make installing the range in another
home as easy as the first installation.
shutter screw