Whirlpool RH3730XLT3 Installatie-instructies en gebruiks- en onderhoudshandleiding - Pagina 3

Blader online of download pdf Installatie-instructies en gebruiks- en onderhoudshandleiding voor {categorie_naam} Whirlpool RH3730XLT3. Whirlpool RH3730XLT3 24 pagina's. 30" (76.2 cm) and 36" (91.4 cm) range hood
Ook voor Whirlpool RH3730XLT3: Onderdelenlijst (1 pagina's), Installatie-instructies en gebruiks- en onderhoudshandleiding (24 pagina's)

Pagina afdrukken
iMPORTANT SAFETY iNSTRUCTiONS
WARNING:
TO REDUCE THE RiSK OF FIRE, ELECTRIC
SHOCK, OR iNJURY TO PERSONS, OBSERVE THE
FOLLOWING:
• Use this unit only in the manner intended by the
manufacturer,
if you have questions, contact the
manufacturer.
• Before servicing or cleaning the unit, switch power off at
service panel and Iock the service disconnecting
means to
prevent power from being switched on accidentalIy. When
the service disconnecting
means cannot be locked,
securely fasten a prominent warning device, such as a tag,
to the service panel.
• InstaIIation work and electrical wiring must be done by
qualified person(s) in accordance with aII appIicabJe codes
and standards, including fire-rated construction.
• Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fueI
burning equipment to prevent backdrafting. Foilow the
heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning
Engineers
(ASHRAE), and the Iocal code authorities.
• When cutting or drilling into walI or ceiling; do not damage
electrical wiring and other utilities.
• Ducted fans must always be vented outdoors.
CAUTION:
For general ventilating use only. Do not use
to exhaust hazardous or explosive materials and vapors.
CAUTtON:
To reduce risk of fire and to properly exhaust
air, be sure to duct air outside - do not vent exhaust air into
spaces within wails or ceilings, attics or into crawl spaces,
or garages.
WARNING:
TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
WARNING:
TO REDUCE THE RiSK OF A RANGE TOP
GREASE FIRE:
• Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spiIIovers that may
ignite. Heat oils slowly on Iow or medium settings.
• Always turn hood ON when cooking at high heat or when
fiambeing food (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flamb6).
• Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
• Use proper pan size. Always use cookware appropriate for
the size of the surface element.
WARNING:
TO REDUCE THE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGE TOP GREASE
FIRE, OBSERVE THE FOLLOWING: _
• SMOTHER FLAMES with a close fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
• NEVER PICK UP A FLAMING PAN - you may be burned.
• DO NOT USE WATER, including wet dishcloths or towels -
a violent steam explosion will result.
• Use an extinguisher ONLY if:
- You know you have a class ABC extinguisher,
and you
already know how to operate it.
- The fire is smaII and contained in the area where it
started.
- The fire department is being called.
- You can fight the fire with your back to an exit.
aBased on "Kitchen Fire Safety Tips" published by NFPA.
• WARNING:
To reduce the risk of fire or electrical shock,
do not use this fan with any solid-state speed control
device.
SAVE THESE iNSTRUCTiONS
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Drill
•
11/4"drill bit
•
1/8"(3 mm) drill bit for pilot holes
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Caulking gun and weatherproof
caulking compound
•
Flat-blade screwdriver
•
Phillips screwdriver
For vented installations, you also need:
•
Saber or keyhole saw
•
Vent clamps
•
Metal snips
•
Compass or 8" (20.3 cm) circle template
Parts supplied
Remove parts from package. Check that all parts are included.
•
Filter
•
4 - #10 x %"mounting
screws
•
7" (17.8 cm) round transition plate
•
7" (17.8 cm) damper/vent
connector
•
31/4 '' x 10" (8.3 x 25.4 cm) damper/vent
connector