Whirlpool Slide-Out Range Hood Installatie- en gebruikshandleiding - Pagina 5

Blader online of download pdf Installatie- en gebruikshandleiding voor {categorie_naam} Whirlpool Slide-Out Range Hood. Whirlpool Slide-Out Range Hood 36 pagina's. 30" (76.2 cm) and 36" (91.4 cm) slide-out range hood

Pagina afdrukken
9 "
(24.1 cm)
Shelf extends
7" (17.8 cm)
1"
(25.4 mm)
11"
(27.9 cm)
Cabinet Dimensions
30" (76.2 cm) or
36" (91.4 cm) min.
cabinet opening width
24" (61 cm) min.
30" (76.2 cm)
suggested max.
bottom of cabinet
to cooking surface
15" (38.1 cm)
min. clearance
upper cabinet
to countertop
36" (91.4 cm)
base cabinet
height
Product Dimensions
FRONT OF
RANGE HOOD
30" (76.2 cm) model: 26" (66.0 cm)
36" (91.4 cm) model: 32" (81.3 cm)
(25.4 cm)
2 "
(6.0 cm)
2"
(5.1 cm)
8"
(20.3 cm)
1 "
(31.8 mm)
(41.3 mm)
" to
(1.6 cm to 5.4 cm)
9 "
(23.2 cm)
1
"
(3.6 cm)
13" (33 cm)
cabinet depth
30" (76.2 cm) model: 8" (20.3 cm)
36" (91.4 cm) model: 11" (27.9 cm)
4 "
(11.1 cm)
10"
30" (76.2 cm) model: 13" (33.0 cm)
36" (91.4 cm) model: 16" (40.6 cm)
"
(6.4 mm)
1 "
"
BACK OF
RANGE HOOD
30" (76.2 cm) model: 29 " (75.9 cm)
36" (91.4 cm) model: 35 " (91.1 cm)
2"
(5.1 cm)

Venting Requirements

Vent system must terminate to the outside, except for non-
vented (recirculating) installations.
Do not terminate the vent system in an attic or other enclosed
area.
Do not use a 4" (10.2 cm) laundry-type wall caps.
Use a metal vent only. A rigid metal vent is recommended.
Plastic or metal foil vent is not recommended.
The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
For the most efficient and quiet operation:
Use no more than three 90° elbows.
Make sure there is a minimum of 24" (61.0 cm) of straight
vent between the elbows if more than 1 elbow is used.
Do not install 2 elbows together.
The vent system must have a damper. If the roof or wall cap
has a damper, do not use the damper supplied with the range
hood.
Use clamps to seal all joints in the vent system.
Use caulking to seal exterior wall or roof opening around the
cap.
The size of the vent should be uniform.
Cold weather installations
An additional back draft damper should be installed to minimize
backward cold air flow and a thermal break should be installed to
minimize conduction of outside temperatures as part of the vent
system. The damper should be on the cold air side of the thermal
break.
The break should be as close as possible to where the vent
system enters the heated portion of the house.
3 " (8.3 cm)
" (9.5 mm)
(vented models only)
5