AER combi-SUB 15 Gebruikershandleiding - Pagina 7
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} AER combi-SUB 15. AER combi-SUB 15 9 pagina's.
5. Technical data
4. Technical data
Input connections
input
Electronically balanced line input
Unbalanced jack connection also possible
Combo socket, XLR + jack ¼" (6.35 mm)
Nominal input voltage: 1 V (0 dBV)
Min. input voltage:
Combi Sub 12: 360 mV (–9 dBV)
Combi Sub 15: 400 mV (–8 dBV)
Max. input voltage: 9 V (+19 dBV)
Input impedance: 20 k
Equivalent input noise voltage (A-weighted):
6.5 µV (–104 dBV)
link
XLR output, directly connected to input
clip
Headroom 6 dB
indicator
Active crossover
Filter type
Butterworth lowpass, 12 dB/oct.
Crossover
Adjustable, 70 – 200 Hz
frequency
Notch filter
Notch
Adjustable, 50 – 300 Hz
frequency
Notch
-14 dB
attenuation
Bandwidth
0.7 octaves between –6.5 dB points
Notes
Switchable
Power
Combi Sub 12: 200 W / 8 (1% THD)
Power amp
Combi Sub 15: 250 W / 8 (1% THD)
Discrete bipolar transistor output
Residual noise (A-weighted):
260 µV (–72 dBV)
Dynamic range (A-weighted):
104 dB
Mains power
Mains voltage (depending on model):
100, 120, 230, or 240 V AC, 50–60 Hz
Power consumption:
Combi Sub 12: max. 500 W
Combi Sub 15: max. 600 W
Mains fuse
Size: 5 x 20 mm
Rating:
For 230 and 240 V models: T 3.15 A L / 250 V
For 100 and 120 V models: T 6.3 A L / 250 V
General
Distortion
THD + N < 0.1 % at 25 W / 8
(electrical)
Signal
Subsonic filter, RMS limiter
processing
Limiter
Combi Sub 12: 160 W / 8
threshold
Combi Sub 15: 220 W / 8
Speaker
Combi Sub 12: 300 mm (12") woofer
system
Combi Sub 15: 380 mm (15") woofer
Bass reflex enclosure
Cabinet
18 mm (0.71") birch plywood
M20 thread for speaker stand on top side
Finish
Waterbased acrylic, black spatter finish
Dimensions and weight
Dimensions
Combi Sub 12:
430 mm (16,92") high
490 mm (19,29") wide
350 mm (13,77") deep
Combi Sub 15:
490 mm (19.29") high
560 mm (22.05") wide
440 mm (17.32") deep
Weight
Combi Sub 12: 19,55 kg (43,1 lbs)
Combi Sub 15: 29 kg (64 lbs)
NOTES
Rated conditions:
Input signal: 100 Hz sine, nominal input voltage applied
Crossover (frequency) control fully clockwise.
Notch filter off.
Level adjusted such that the rated output power is obtained
if the limiter is disabled (Level in center position
approximately).
Signal voltages stated as RMS values.
0 dBV corresponds to 1 V RMS.
Min. input voltage: Input voltage required for rated output
power (without limiter) with level fully clockwise
Max. input voltage: Input voltage that does not cause more
than 1% THD+N, suitable control settings provided
THD + N: Total harmonic distortion + noise, with input and
output levels 10 dB below rated conditions.
Equivalent input noise voltage: Noise voltage at speaker
output divided by gain of amplifier at 100 Hz. Control
settings as stated under rated conditions. Measurement
range: 20 Hz – 20 kHz. Input shorted.
Residual noise: Output noise when the level control is set to
minimum.
Dynamic range: Ratio of nominal output voltage to residual
noise voltage
Specifications and appearance subject to change without
notice.
TD20130827
7