Xerox DocuPrint 115 Referentiehandleiding - Pagina 2
Blader online of download pdf Referentiehandleiding voor {categorie_naam} Xerox DocuPrint 115. Xerox DocuPrint 115 2 pagina's. Tape client job submission guide enterprise printing system
Ook voor Xerox DocuPrint 115: Bedieningshandleiding (38 pagina's), Specificaties (2 pagina's), Bedieningshandleiding (34 pagina's), Handleiding voor planning (20 pagina's), Snelle referentie (2 pagina's), Aanvullende handleiding (48 pagina's)
Pagina afdrukken
Environmental requirements
Recommended
Minimum Maximum
o
o
o
o
Operating
72
+/- 4
F
50
F
85
temperature
o
o
o
o
22
+/- 2
C
10
C
29
Humidity
45% +/- 10% RH 30% RH
65% RH
Normal
Maximum
Altitude
Up to 6,000 feet /
9,000 feet /
1,830 m above
2,743 m above
sea level
sea level
Heat dissipation
Standby
Running
Printer
4,454 BTU/hr.
155/180: 32,770
(Fuser on)
BTU/hr
2,700 BTU/hr.
100/115/135:
(Energy saver)
28,140 BTU/hr.
Processor and
SB 1000/2000: 1,100 BTU/hr.
monitor (Sun
SB 2500: 1,570 BTU/hr.
TM
Blade
)
Supplies
Expected yield
Reorder number
(Prints/carton)
Dry ink
US: 6R206
180,000
Europe: 6R90100
Dry ink waste
US: 93K460
N/A
bottle
Europe: 93K450
Developer
US: 5R161
1,000,000
Europe: 5R90095
Fuser agent
US: 8R2955
250,000
Europe: 8R90163
(1 bottle)
MICR dry ink
US: 6R819
180,000
MICR
US: 5R573
600,000
developer
Notes:
•
Expected dry ink yield is based on a 7 percent area
coverage, 8.5 by 11 inch or A4 paper, and varies
depending on area coverage of the application, as
well as the darkness settings of the printer.
•
Contact your local Xerox representative for supplies
ordering information.
•
In the U.S., call 1.800.822.2200 to order Xerox
supplies, including paper and other stocks.
Space requirements
F
Depth
C
Controller
The following data is accurate for the Sun Blade
1000/2000 and 2500 workstations, and is presented
as an example of typical space requirements for
workstations.
Stand
35.5
in.
90.2
cm
19.3
Processor: Sun
in.
TM
Blade
1000/2000
49
cm
25
Processor: Sun
in.
TM
Blade
2500
63.5
cm
Monitor
10 in.
25.4 cm
Printer
Space requirements (physical hardware and required
service area) for each of the printer configurations:
With inverter feeder/
114 in.
stacker and 1 feeder/
290 cm
stacker
With inverter feeder/
114 in.
stacker and 2 feeder/
290 cm
stackers
With inverter feeder/
114 in.
stacker and 3 feeder/
290 cm
stackers
With inverter feeder/
114 in.
stacker, feeder/
290 cm
stacker, and bypass
transport module
With inverter feeder/
114 in.
stacker and 2 feeder/
290 cm
stackers, and bypass
transport
Notes:
•
All the dimensions are taken from the system frame
to the nearest wall or obstruction, shown in inches
and centimeters, and are absolute minimums.
•
There should be a minimum of 78 inches / 198 cm
clearance from the floor to the nearest overhead
obstruction, throughout the entire area.
•
The printing system must be installed in a fixed
location with minimum clearance space of 36 inches
/ 91.4 cm around all sides of each piece of
equipment for access by service personnel.
•
50 inches / 127 cm clearance space is required in
Width
Height
front of the printer.
•
The controller must be positioned within the line of
sight of the printer for safety purposes while the
TM
equipment is being serviced.
•
Customer must use the Xerox-supplied stand for all
controller components. Space requirements for the
controller stand are 36 by 36 inches / 91 by 91 cm.
30 in.
38.25 in.
•
For proper operation, the printer must be perfectly
76.2 cm
97.2 cm
level. On floors less than two degrees out of level, a
leveling kit must be used to level the equipment.
8.2 in.
17.75 in.
The printer will not function properly on floors more
than two degrees out of level.
21 cm
45.1 cm
For additional space/configuration options, refer to the
10 in.
19 in.
Xerox DocuPrint 100/115/135/155/180 EPS
Installation Planning Guide.
25.4 cm
46.3 cm
Electrical requirements
17 in.
18.5 in.
43.2 cm
47 cm
Controller
(47-63 Hz)
Voltage
100-240
VAC
223 in.
(1 phase)
567 cm
257 in.
Recep-
5-15R
652.8 cm
tacle
NEMA part
288 in.
number
731 cm
Power
0.4
consump-
tion (KVA)
242 in.
Operating
615 cm
mode
276 in.
Notes:
701 cm
•
Dedicated service is required for each component.
Each power cord must have a separate circuit.
•
Power requirements of the bypass transport are
satisfied by the printer module.
2004 by Xerox Corporation. All rights reserved.
Xerox DocuPrint
100/115/135/155/180 EPS
Customer Information
Quick Reference Card
155/180
Printer
printer
Printer
(60 Hz)
(60 Hz)
(50 Hz)
Cord #1
Cord #2
120/208
120/208
380, 400,
VAC; or
VAC; or
415 VAC
120/240
120/240
(3 phase)
VAC
VAC
(2 phase)
(2 phase)
14-50R
14-30R
--
7.3 +
7.3+
Consult
.75 per
.75 per
your local
middle
middle
service
module
module
represent
stacker
stacker
ative
Version 4.1
September 2004
701P42238