Yamaha Clavinova CLP-920 Gebruikershandleiding - Pagina 20

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Yamaha Clavinova CLP-920. Yamaha Clavinova CLP-920 32 pagina's. Yamaha clavinova owner's manual

Pagina afdrukken

MIDI Data Format/MIDI-Datenformat/Format des données MIDI/Formato de datos MIDI

MIDI Master Volume

• Simultaneously changes the volume of all channels.

• When a MIDI master volume message is received, the volume

only has affect on the MIDI receive channel, not the panel master

volume.

F0H

= Exclusive status

7FH

= Universal Realtime

7FH

= ID of target device

04H

= Sub-ID #1=Device Control Message

01H

= Sub-ID #2=Master Volume

ll H

= Volume LSB

mmH

= Volume MSB

F7H

= End of Exclusive

F0H

= Exclusive status

7FH

= Universal Realtime

XnH

= When received, n=0~F. X = don't care

04H

= Sub-ID #1=Device Control Message

01H

= Sub-ID #2=Master Volume

ll H

= Volume LSB

mmH

= Volume MSB

F7H

= End of Exclusive

(2) Universal Non-Realtime Message (GM 0n)

General MIDI Mode On

Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] -> [F7H]

F0H

= Exclusive status

7EH

= Universal Non-Realtime

7FH

= ID of target device

09H

= Sub-ID #1=General MIDI Message

01H

= Sub-ID #2=General MIDI On

F7H

= End of Exclusive

F0H

= Exclusive status

7EH

= Universal Non-Realtime

XnH

= When received, n=0~F. X = don't care

09H

= Sub-ID #1=General MIDI Message

01H

= Sub-ID #2=General MIDI On

F7H

= End of Exclusive

When the General MIDI mode ON message is received, the MIDI

system will be reset to its default settings.

This message requires approximately 50ms to execute, so sufficient

time should be allowed before the next message is sent.

7. SYSTEM EXCLUSIVE MESSAGES (XG Standard)

(1) XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->

[mmH] -> [ll H] -> [ddH] -> [F7H]

F0H

= Exclusive status

43H

= YAMAHA ID

1nH

= When received, n=0~F. When transmitted, n=0.

4CH

= Model ID of XG

hhH

= Address High

mmH

= Address Mid

ll H

= Address Low

ddH

= Data

F7H

= End of Exclusive

Data size must match parameter size.

When the XG System On message is received, the MIDI system will

be reset to its default settings.

The message requires approximately 50ms to execute, so sufficient

time should be allowed before the next message is sent.

MIDI Parameter Change table ( SYSTEM )

Address (H)

Size (H)

00 00 00

TOTAL SIZE

*1: Values lower than 020CH select -50 cents. Values higher than 05F4H select +50 cents.

*2: Values from 28H through 33H are interpreted as -12 through -1. Values from 4DH through 58H are interpreted as +1 through +12.

CLP-920

Data (H)

Parameter

020C - 05F4(*1) MASTER TUNE

00 - 7F

MASTER VOLUME

—

34 - 4C(*2)

TRANSPOSE

XG SYSTEM ON

RESET ALL PARAMETERS

(2) XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->

[bbH] -> [hhH] -> [mmH] -> [ll H] ->

[ddH] ->...-> [ccH] -> [F7H]

F0H

Exclusive status

43H

YAMAHA ID

0nH

When received, n=0~F. When transmitted, n=0.

4CH

Model ID of XG

aaH

ByteCount

bbH

ByteCount

hhH

Address High

mmH

Address Mid

ll H

Address Low

ddH

Data

ccH

Check sum

F7H

End of Exclusive

• Receipt of the XG SYSTEM ON message causes reinitialization of

relevant parameters and Control Change values. Allow sufficient

time for processing to execute (about 50 msec) before sending the

Clavinova another message.

• XG Native Parameter Change message may contain two or four

bytes of parameter data (depending on the parameter size).

• For information about the Address and Byte Count values, refer to

Table 1 below. Note that the table's Total Size value gives the size of

a bulk block. Only the top address of the block (00H, 00H, 00H) is

valid as a bulk data address.

8. SYSTEM EXCLUSIVE MESSAGES (Special Control)

Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [11H] ->

[0nH] -> [ccH] -> [vvH] -> [F7H]

F0H

= Exclusive status

43H

= Yamaha ID

73H

= Clavinova ID

67H

= CLP-920 ID

11H

= Clavinova special control

0nH

= Control MIDI change (n=channel number)

= Control number

= Value

F7H

= End of Exclusive

Control

Voice Reserve

ch: 00H-0FH

* When Volume, Expression is received for Reserve On, they will be

effective from the next Key On. Reserve Off is normal.

9. SYSTEM EXCLUSIVE MESSAGES (Others)

Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] ->

[00H] -> [00H] -> [mmH] -> [ll H] -> [ccH] -> [F7H]

Master Tuning (XG and last message priority) simultaneously

changes the pitch of all channels.

F0H

= Exclusive Status

43H

= Yamaha ID

1nH

= Transmission from n=CLP is always 0. 0-F is received.

27H

= Model ID of TG100

30H

= Sub ID

00H

mmH

= Master Tune MSB

ll H

= Master Tune LSB

ccH

= don't care (under 7FH)

F7H

= End of Exclusive

Description

-50 - +50[cent]

1st bit 3 - 0 → bit 15 - 12

2nd bit 3 - 0 → bit 11 - 8

3rd bit 3 - 0 → bit 7 - 4

4th bit 3 - 0 → bit 3 - 0

0 - 127

-12 - +12[semitones]

00=XG sytem ON

00=ON (receive only)

ccH

vvH

45H

00H : Reserve off

7FH : on*

Default value (H)

00 04 00 00

400